Agilent Technologies PL-GPC 220 Скачать руководство пользователя страница 54

Страница: 54 / 120

PL-GPC 220 User Manual

Using the Module

Running Samples on the PL-GPC 220

Loading the Samples

Pull out the autosampler carousel drawer.

Load the autosampler carousel with the sample and rinse vials in the
appropriate vial positions.

Firmly push the autosampler carousel drawer back into position.

You will hear an audible

click

as the autosampler fits into place.

Ensure that the data collection software you are using is ready to collect
and the sequence run list has been defined (remember data will not be
collected for rinse vials).

On the autosampler area of the Control software, click the

Autosampler

Offline

button.

This will now change to

Autosampler Online

and the sequence will begin. You

can follow the status of the run sequence in the software.

At any time, you can stop the autosampler sequence by clicking the

Autosampler Online

button.

The software will then prompt you to select a new start vial if the sequence
is restarted.

Preparations

•

Start the log file to monitor the condition of the instrument during operation.

•

Ensure that there is sufficient eluent to carry out the analysis (you can use the

time estimator

tool on the Control software once you have defined the autosampler sequence).

•

Ensure that there is sufficient capacity in the waste container.

Содержание PL-GPC 220

























































































































Результаты поиска

Содержание PL-GPC 220

Отзывы:

Бренды по названию

Популярные бренды

Agilent Technologies PL-GPC 220, Руководство пользователя

Результаты поиска

Содержание PL-GPC 220

Отзывы:

Бренды по названию

Популярные бренды