Agilent Technologies E3631-90002 Скачать руководство пользователя страница 77 | Manualshive

Страница: 77 / 166

Agilent Technologies E3631-90002 Скачать руководство пользователя страница 77

Chapter 4 Remote Interface Reference

Output Setting and Operation Commands

76

INSTrument:COUPle[:TRIGger]?

This query returns the currently coupled output. Returns “ALL”, “NONE”, or
a list. If any output is not coupled, “NONE” is returned. If all of three
outputs are coupled, “ALL” is returned. If a list of outputs is coupled, the list
is returned.

Measurement Commands

MEASure:CURRent[:DC]? [{P6V | P25V | N25V}]

This command queries the current measured at the

output terminals

of the

power supply. The physical outputs of measurement are specified by the
output identifier. If any output identifier is not specified, the current of the
currently selected output is returned.

MEASure[:VOLTage][:DC]? [{P6V | P25V | N25V}]

This command queries the voltage measured at the

output terminals

of the

power supply. If any output identifier is not specified, the voltage of the
currently selected output is returned.

«
...
75
76
77
78
79
...
»

Содержание E3631-90002







































































































































































Отзывы:

Нет отзывов