Agilent Technologies E3631-90002 Скачать руководство пользователя страница 55 | Manualshive

Страница: 55 / 166

Agilent Technologies E3631-90002 Скачать руководство пользователя страница 55

Chapter 3 Front-Panel Operation

RS-232 Interface Configuration

54

RS-232 Interface Configuration

You connect the power supply to the RS-232 interface using the 9-pin (DB-9)
serial connector on the rear panel. The power supply is configured as a DTE
(Data Terminal Equipment) device. For all communications over the RS-232
interface, the power supply uses two handshake lines: DTR (Data Terminal
Ready, on pin 4) and DSR (

Data Set Ready

, on pin 6).

The following sections contain information to help you use the power supply
over the RS-232 interface. The programming commands for RS-232 are
explained on page 87.

RS-232 Configuration Overview

Configure the RS-232 interface using the parameters shown below. Use
the front-panel

key to select the baud rate, parity, and

number of data bits (see page 51 for more information to configure from
the front panel).

• Baud Rate: 300, 600, 1200, 2400, 4800, or

9600

baud (

factory setting

)

• Parity and Data Bits:

None / 8 data bits

(

factory setting

)

Even / 7 data bits, or
Odd / 7 data bits

• Number of Start Bits:

1 bit

(

fixed

)

• Number of Stop Bits:

2 bits

(

fixed

)

RS-232 Data Frame Format

A character

frame

consists of all the transmitted bits that make up a single

character. The frame is defined as the characters from the

start bit

to the

last

stop bit

, inclusively. Within the frame, you can select the baud rate,

number of data bits, and parity type. The power supply uses the following
frame formats for seven and eight data bits.

I/O Config

«
...
53
54
55
56
57
...
»

Содержание E3631-90002







































































































































































Отзывы:

Нет отзывов