manualshive.com logo in svg

AEG THYRO-A, Руководство по эксплуатации

Поделиться
Скачать
AEG THYRO-A Скачать руководство пользователя страница 36

36

4.  Settings and operation

DANGER
Dangers involved in settings and operation

Risk of injury / Risk of damage to the device or plant

• Observe all safety regulations in the chapter on safety.
Setting and operating the thyristor power controller is described in this 
chapter.
There are three ways of setting the power controller:
• on DIP switches and potentiometers (on device)
• via bus system (when operated in a bus system)
• via PC interface and THYRO-TOOL FAMILY
Certain settings can only be made on the device (DIP switch S1.7, S1.8 
and S1.10), e.g. setting the analog input and output.
In the case of certain configurations / connection types, setting on the 
device itself is no longer possible:
•  Operation with bus module (see also page 64, Connecting the bus 

module)

   -   Ground to X22.1: Setpoint comes from bus. DIP switch and potenti-

ometer are read in once after being switched on and the setting can 
then be changed with the bus module.

   -   No ground to X22.1: DIP switch and potentiometer are always read 

in. Setpoint is read via the analog input.

• Operation with THYRO-TOOL FAMILY
    -  Device in Thyro-Tool mode: DIP switch and potentiometer are igno-

red. Settings are read out of the memory and can only be changed 
via the PC.

   -  Device not in Thyro-Tool mode: DIP switch and potentiometer are 

read in. Further settings can be changed via the PC. All parameters 
are visualized on the PC.

NOTE
Described settings

Settings made on the device itself are described in this 
chapter. Where reference is made to settings with a bus 
module or with the PC, this is indicated

Содержание THYRO-A













































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды