manualshive.com logo in svg

AEG THYRO-A, Руководство по эксплуатации, Страница: 14 / 108

Поделиться
Скачать
AEG THYRO-A Скачать руководство пользователя страница 14

14

•  The operating conditions and restrictions resulting from the technical 

data are observed.

•  Should abnormal voltages, noises, increased temperatures, vibra-

tion or similar occur, the device is immediately put out of operation 
and the maintenance personnel is informed.

2.4   Personnel requirements

•  Only qualified electro-technical personnel who are familiar with the 

pertinent safety and installation regulations may perform the follow-
ing:

- transport
- installation
- connection
- commissioning
- maintenance
- testing
- operation.
•  These operating instructions must be read carefully by all persons 

working with or on the equipment prior to installation and initial start-
up.

2.5   Intended use

The device may only be used for the purpose for which it was inten-
ded, as persons may otherwise be exposed to dangers (e. g. electric 
shock, burns) and plants also (e. g. overload). The user must therefo-
re observe the following points:
•  It is not permitted to make any unauthorised modifications to the unit 

or to use any spare parts or replacement parts not approved by AEG 
PS, or to use the unit for any other purpose.

•  The warranty obligations of the manufacturer are only applicable if 

these operating instructions are observed and complied with.

•  The device may only be used for control and regulation of electrical 

power.

• The device is a component that cannot function alone.
• Project planning must account for the proper use of the device.
•  Never exceed the maximum permitted connection values as given 

on the type plate.

Содержание THYRO-A













































































































Отзывы:

Нет отзывов