manualshive.com logo in svg

AEG THYRO-A, Руководство по эксплуатации

Поделиться
Скачать
AEG THYRO-A Скачать руководство пользователя страница 15

15

EN

•  The device may only be operated in conjunction with a connected 

ahead mains disconnect device (e. g. switch, VDE 0105 T1).

•  It must be guaranteed that in the event of a fault, no uncontrolled 

currents, voltages or power may occur in the circuit.

•  Despite proper use, it is possible in the event of a fault, that the 

device will not control the currents, voltages and power in the load 
circuit (example: if the power components are destroyed (broken 
down or high-resistance), the following reactions are possible: cur-
rent interrupted, half wave operation, permanent flow of power).

2.6   Use of the device

2.6.1  Operation

•  Only switch on the mains voltage at the device when there is no 

danger to persons, system or load.

• Protect the device against dust and damp.
• Ensure that the ventilation openings are not blocked

2.6.2  Prior to installation / commissioning

•  If stored in a cold environment: ensure that the device is absolutely 

dry. (Allow the device a period of at least two hours to acclimatise 
before commissioning)

•  Check that the voltage data on the type plate matches the mains 

voltage.

• Only install the device in an upright position.
• Ensure sufficient ventilation of the cabinet if mounted in a cabinet.
•  Observe minimum spacing (clearance: 150 mm above, 100 mm be-

low). The devices can be installed next to each other without spa-
cing between.

•  Ensure that the device cannot be heated up by heat sources below 

it. (The power loss is given in the type overview table, see page 87, 
Technical data).

•  Ground the device in accordance with local regulations.
•  Connect the device to the mains and the corresponding load in ac-

cordance with the connection diagrams.

•  The device is parameterised when delivered. The parameters are 

adapted to the particular power unit. (Default: operating mode VAR 
without N-conductor). Check default settings and adjust to appli-

Содержание THYRO-A













































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды