background image

9

Safety Instructions for Users

Inform users of the sunbed about the following safety instructions or make 

them available to users in printed form: 
■  UV-light can cause severe  damage to your skin and your eyes!  

■  Children and young adolescents are not allowed to use a sunbed.

■  Persons with very light skin, many freckles, fair to reddish hair and light 

eyes and nipples are not allowed to use a sunbed.

■  Always wear protective eye-wear during a tanning session and close 

your eyes.

■  Remove contact lenses prior to a tanning session.

■  Remove make-up or any cosmetics well in advance of a tanning 

session. Cosmetics may have unwelcome side effects and can cause 

adverse skin reactions. 

■  Take only one (1) tanning session per day.

■  For the first two sessions observe an interval of 48 hours.

■  For the following sessions, observe an interval of minimum 24 hours 

between sessions. 

■  After a tanning session, do not tan in the natural sun on the same day. 

■  Stop exposure immediately when you notice physical symptoms or 

adverse skin reactions. If the symptoms do not disappear after a short 

time, consult a dermatologist.

■  Do not use drugs which promise to tan the skin without UV-light 

exposure in combination with a tanning session.  This combination may 

increase the risk of a sunburn. 

■  Do not use any self-tanning creams or lotions. These products may 

contain ingredients which can increase the effects of UV-light exposure 

in an unforeseen and unwelcome way.  

■  Do not use any creams or lotions with a suncreen designed for outdoor 

tanning.  These products may contain substances which can influence 

the effects of artificial UV light exposure in an unwelcome way. Use only 

products designed specifically for indoor tanning. 

■  Immoderate tanning results in overexposure. If skin shows signs of 

blisters or sores or shows symptoms of irritation, consult physician or 

dermatologist immediately. 

■  Overexposure to UV-light emitted by either the sun or indoor tanning 

equipment can cause premature aging of the skin and increase the risk 

of skin cancer. 

■  The unprotected eye can catch conjunctivitis and in some cases 

overexposure can seriously damage the retina. Repeated exposures 

increase the risk of cataracts. 

Содержание ICON






































































































Отзывы:

Похожие инструкции для ICON