background image

TABLE OF CONTENTS

1.0 Safety ....................................................................................................................................................................................... 1

1.1 Safety Messages ........................................................................................................................................................................................................ 1

1.1.1 Introduction to Safety ................................................................................................................................................................................. 2

1.1.2 Intended Use .................................................................................................................................................................................................. 2

1.1.3 Material Handling Precautions: Storage .............................................................................................................................................. 3

1.1.4 Operation Safety ........................................................................................................................................................................................... 3

1.1.5 Maintenance Safety ..................................................................................................................................................................................... 3

1.1.6 Material Handling Precautions: Fasteners ..........................................................................................................................................  4

1.1.7 Material Handling Precautions, ESD .....................................................................................................................................................  4

2.0 About this Manual .................................................................................................................................................................  5

2.1 How to work with the manual .............................................................................................................................................................................. 5

2.2 Abbreviations and terms - AGL ...........................................................................................................................................................................  5

2.3 Abbreviations and Terms ........................................................................................................................................................................................ 5

3.0 General Information ..............................................................................................................................................................  7

3.1 Introduction to RELIANCE ...................................................................................................................................................................................... 7

3.2 LED Apron Maneuvering ........................................................................................................................................................................................ 8

3.3 LED Taxiway Edge ...................................................................................................................................................................................................... 9

4.0 Installation ............................................................................................................................................................................ 13

4.1 Unpacking the Unit ................................................................................................................................................................................................ 13

4.2 Tools required ..........................................................................................................................................................................................................  13

4.3 Installation and removal of the 8-inch light fixture ................................................................................................................................... 14

5.0 Operation .............................................................................................................................................................................. 17

5.1 RELIANCE Intelligent Lighting ...........................................................................................................................................................................  17

5.2 RELIANCE IQ and the 2A Concept ................................................................................................................................................................... 17

5.3 Sensor Interface Unit (SIU) .................................................................................................................................................................................. 17

5.4 Network Concentrator Unit (NCU) ................................................................................................................................................................... 17

5.5 Series Circuit Modem (SCM) .............................................................................................................................................................................. 17

5.6 Series Circuit Filter (SCF) ...................................................................................................................................................................................... 17

5.7 Control System Interface ..................................................................................................................................................................................... 17

5.8 Programming RELIANCE IQ ................................................................................................................................................................................ 18

5.8.1 Hardware equipment setup ................................................................................................................................................................... 18

5.8.2 Software Programming ...........................................................................................................................................................................  20

5.9 Connection in a Series Circuit ............................................................................................................................................................................ 24

5.9.1 Operational characteristics ..................................................................................................................................................................... 24

5.9.2 Power On or Default State ...................................................................................................................................................................... 24

5.9.3 Safe State ......................................................................................................................................................................................................  24

5.9.4 Command Memory ................................................................................................................................................................................... 25

5.9.5 Soft ON/OFF ................................................................................................................................................................................................ 25

5.9.6 Sequenced Flashing .................................................................................................................................................................................. 25

6.0 Maintenance ......................................................................................................................................................................... 27

6.1 Safety instructions .................................................................................................................................................................................................. 27

6.2 Safety Considerations ........................................................................................................................................................................................... 27

6.3 Basic Maintenance Program ............................................................................................................................................................................... 28

6.4 Workshop Maintenance ....................................................................................................................................................................................... 28

6.4.1 Exploded View ............................................................................................................................................................................................. 30

6.4.2 Opening a 8

inch fixture .........................................................................................................................................................................  31

6.4.3 Closing a 8

inch fixture ............................................................................................................................................................................ 31

6.4.4 Checking the light fixture for watertightness ................................................................................................................................. 33

6.4.5 Replacing a Light Engine in a 8

inch Fixture ...................................................................................................................................  34

6.4.6 Replacing the Top Cover ......................................................................................................................................................................... 36

6.4.7 Replacing the Connection Board ......................................................................................................................................................... 39

6.4.8 Replacing the LED Board ......................................................................................................................................................................... 42

UM-5027, Rev. 1.0, 2020/12/10

v

Copyright 

©

 ADB SAFEGATE, All Rights Reserved

Содержание RELIANCE













































































Отзывы: