ADB Safegate RELIANCE Скачать руководство пользователя страница 17

Страница: 17 / 76

3.0 General Information

WARNING

Read installation instructions in their entirety before starting installation.

•

Become familiar with the general safety instructions in this section of the manual before installing, operating,

maintaining or repairing this equipment.

•

Read and carefully follow the instructions throughout this manual for performing specific tasks and working with

specific equipment.

•

these warnings may result in serious injury or equipment damage.

Figure 1: RELIANCE Omni, 4 prisms

3.1 Introduction to RELIANCE

RELIANCE - the all in one revolution
The RELIANCE omnidirectional light light is a low protrusion light-emitting diode (LED) fixture, available in three versions:

RELIANCE

A LED light fixture with integrated fail open technology with CCR monitoring

compatibility

RELIANCE IQ

A RELIANCE with additional and integrated intelligence (IQ) in a built-in converter for

individual monitoring and control, based on RELIANCE Intelligent Light Control and

Monitor System (ILCMS)

RELIANCE IQ0 RELIANCE IQ light fixture with disabled IQ (ILCMS) functionality. Non-MON light fixture

with possibility to activate IQ at a later stage

NOTICE

RELIANCE IQ light fixtures are not fail-open light fixtures. When IQ is activated the monitoring as well as the control

functionality is handled by the ILCMS system.

UM-5027, Rev. 1.0, 2020/12/10

Содержание RELIANCE



































































Результаты поиска

Содержание RELIANCE

Отзывы:

Похожие инструкции для RELIANCE

Бренды по названию

Популярные бренды

ADB Safegate RELIANCE, Руководство пользователя

Результаты поиска

Содержание RELIANCE

Отзывы:

Похожие инструкции для RELIANCE

Бренды по названию

Популярные бренды