ADB Safegate RELIANCE Скачать руководство пользователя страница 50 | Manualshive

Страница: 50 / 76

background image

4. Insert the new connection board with the isolation board on the top cover.
5. Connect the cables to the connection board.
6. Connect the connection board with the isolation board on the top cover.

Note

There are two different types of connectors (entry cables) that are led from the converter to the LED board (and

not to the LED modules). The black one (4 pieces of 70 mm each) connect the connection board with the LED

boards and the red connectors (2 pieces of 180 mm each) connect the connection board with the converter. The

cables are available separately in a cable kit.

Figure 18: Two connector types (replaceable)

RELIANCE Omni Light
Maintenance

40
Copyright

©

ADB SAFEGATE, All Rights Reserved

«
...
48
49
50
51
52
...
»

Содержание RELIANCE













































































Отзывы:

Нет отзывов

Похожие инструкции для RELIANCE

Бренд: YASKAWA Страницы: 256

Бренд: BADLANDS Страницы: 2

Бренд: Eaton Страницы: 2

Бренд: Eaton Страницы: 2

Бренд: Eaton Страницы: 8

Бренд: H-P Products Страницы: 12

Бренд: YOKOGAWA Страницы: 2

ALICAT SCIENTIFIC PC

Бренд: Halma Страницы: 2

ALICAT SCIENTIFIC PCD

Бренд: Halma Страницы: 46

Бренд: OBSIDIAN CONTROL SYSTEMS Страницы: 13

Бренд: Union Instruments Страницы: 63

disklavier DKC-850

Бренд: Yamaha Страницы: 2

Бренд: GEA Страницы: 47

SYSMAC C500-NC222-E

Бренд: Omron Страницы: 164

Бренд: IBM Страницы: 214

Бренд: STIEBEL ELTRON Страницы: 44

Бренд: Grundfos Страницы: 23

Бренд: Sungrow Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды