ADB Safegate RELIANCE Скачать руководство пользователя страница 41

Страница: 41 / 76

6.4.2 Opening a 8

‑

inch fixture

Removal

1. Place the light fixture upside down and remove the four screws for the bottom cover using an Allen key 4 mm.

Note

Refer to

Figure 5

figure.

2. Lift up the housing and disconnect the LED board cable connector from the LED boards in the top cover.

Note

Refer to Lifting

Figure 6

figure.

NOTICE

Open the light fixture carefully so that you do not damage the LED-board cables.

3. Remove the bottom cover from the top cover.
4. Remove the O-ring gasket from the bottom cover.

Note

Refer to

Figure 7

figure.

Figure 5: Fixture upside down

Figure 6: Lifting up housing

Figure 7: Removing gasket

6.4.3 Closing a 8

‑

inch fixture

Replacement

1. Carefully clean all contact surfaces of the light fixture and of the housing.
2. Install a new O-ring gasket on the bottom cover.

Important

The O-ring gasket must be changed each time the light fixture is disassembled.

3. Connect the LED board cable connector(s) to the supply terminal(s) of the converter in the housing.

NOTICE

Note the orientation and alignment of the LED board cables, which are different between 1 connector and 2

connector versions.
Converters with one connector: The cables should have colored wires towards each other and crossed.
Converters with two connectors: The cables should have colored wires away from each other and crossed.Light

fixtures with only one LED-board need to have its LED-board connected to the LED B channel.

UM-5027, Rev. 1.0, 2020/12/10

Содержание RELIANCE



































































Результаты поиска

Содержание RELIANCE

Отзывы:

Похожие инструкции для RELIANCE

Бренды по названию

Популярные бренды

ADB Safegate RELIANCE, Руководство пользователя

Результаты поиска

Содержание RELIANCE

Отзывы:

Похожие инструкции для RELIANCE

Бренды по названию

Популярные бренды