ADB Safegate RELIANCE Скачать руководство пользователя страница 34

Страница: 34 / 76

5.9 Connection in a Series Circuit

5.9.1 Operational characteristics

RELIANCE

RELIANCE

The extent of use of all RELIANCE IQ functionality is determined by the application. All functionality described in this

document is not necessarily used at a specific installation. This section is a summary of common functionality available in

RELIANCE IQ.

5.9.2 Power On or Default State

IQ is configured to set the lamp to a predefined state when the series circuit is energized. This feature is called default state

and the options are LAMP ON, LAMP OFF or LAMP FLASHING. The option to select depends on the light function for a

RELIANCE IQ fitting and the operative requirements.

5.9.3 Safe State

In case communication between the RELIANCE IQ and the SCM is interrupted or lost, IQ functionality will (after a

programmable timeout) set the lamp to a predefined state known as safe state. Safe state can be set to LAMP ON, LAMP OFF,

LAMP FLASHING or no change.

RELIANCE Omni Light
Operation

24
Copyright

Содержание RELIANCE



































































Результаты поиска

Содержание RELIANCE

Отзывы:

Похожие инструкции для RELIANCE

Бренды по названию

Популярные бренды

ADB Safegate RELIANCE, Руководство пользователя

Результаты поиска

Содержание RELIANCE

Отзывы:

Похожие инструкции для RELIANCE

Бренды по названию

Популярные бренды