ADB Safegate RELIANCE Скачать руководство пользователя страница 60 | Manualshive

Страница: 60 / 76

background image

.

Figure 31: Converter with 1 connector

Figure 32: Converter with 2 connectors

3. Close the light fixture and connect it to a CCR.
4. Energize the light fixture until there is a steady light, then turn the CCR off and unplug the light fixture.
5. Disassemble the light fixture, then remove the two-way electrical shunt (2.54 mm spacing) from the pins.
6. Assemble the light fixture and perform a functional test.

6.4.12 Resetting the Fail-open converters 48010921 and 48011111

Parts

•

Fuse resistor spare part kit: 6132.00.250 (20pcs)

Info

•

Converter with 1 connector have 2 fuse resistors

•

Converter with 2 connectors have 4 fuse resistors

Resetting / replacing the fuse resistors

1. Disconnect and disassemble the light fixture.
2. Locate the fuse resistors.

Note

Refer to

Figure 33: Converter with 1 connector

Figure 34: Converter with 2 connectors

3. Remove the fuse resistors by pulling away from the converter.

a. For converters with 1 connector, always replace both fuse resistors at the same time.

b. For converters with 2 connectors, always replace both fuse resistors related to the A/B channel that needs to be reset.

If both A and B channel needs a reset, replace all 4 fuse resistors.

RELIANCE Omni Light
Maintenance

50
Copyright

©

ADB SAFEGATE, All Rights Reserved

«
...
58
59
60
61
62
...
»

Содержание RELIANCE













































































Отзывы:

Нет отзывов

Похожие инструкции для RELIANCE

Бренд: Watts Страницы: 2

Бренд: unicore Страницы: 25

Бренд: unicore Страницы: 24

Бренд: IBM Страницы: 12

Бренд: K&K Страницы: 10

ROBO Cylinder RCP2 Series

Бренд: IAI Страницы: 5

Бренд: ICM Controls Страницы: 2

Бренд: Parker Страницы: 21

Бренд: Parker Страницы: 26

Бренд: Parallax Страницы: 3

FEBCO 860 Small Series

Бренд: Watts Страницы: 12

Бренд: Bardiani Valvole Страницы: 54

Бренд: Parker Страницы: 478

Cutler-Hammer Jockey

Бренд: Eaton Страницы: 12

Бренд: BendPak Страницы: 43

Бренд: RKC INSTRUMENT Страницы: 10

Бренд: Gemini Страницы: 9

Бренд: M-system Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды