ADB Safegate RELIANCE Скачать руководство пользователя страница 39

Страница: 39 / 76

Important

Make sure you check the fixture for watertightness very time you replaced a spare part!

The following standard tools and accessories are required for maintenance of the unit:

•

One angled socket spanner of 16 or 17 mm

•

One torque limiting spanner with 16 or 17 mm socket

•

One hexagonal key (Allen key) of 3, 4, and 5 mm

•

Torx screw driver 10, 20, 25, and 30 mm

•

Two large flat blade screwdrivers

•

Silicone grease

•

CC-Patron grease

•

One brush or cloth

•

Non-alcohol based cleaner

NOTICE

A compressor, or a manual car tire pump, equipped with a manometer is required to check the light fixture for water-

tightness.
Design may differ from picture depending on application. Please follow described work flow and torque level specified

as they are generic.

The workshop maintenance refers to following:

1. Replace a light fixture.
2. Check the light fixture for watertightness.
3. Replace a light engine.
4. Replace a prism and its gasket.
5. Replace the bottom cover and converter.
6. Reset the fail-open converter.

Depending on type and size of nuts and bolts

UM-5027, Rev. 1.0, 2020/12/10

Содержание RELIANCE



































































Результаты поиска

Содержание RELIANCE

Отзывы:

Похожие инструкции для RELIANCE

Бренды по названию

Популярные бренды

ADB Safegate RELIANCE, Руководство пользователя

Результаты поиска

Содержание RELIANCE

Отзывы:

Похожие инструкции для RELIANCE

Бренды по названию

Популярные бренды