ABB Relion REQ650 Скачать руководство пользователя страница 11

Страница: 11 / 150

Sensitive directional residual overcurrent and power protection

SDEPSDE (67N)................................................................................53

Measuring the operate and time limit for set values.....................53
Completing the test.......................................................................58

Thermal overload protection, one time constant, Fahrenheit/

Celsius LFPTTR/LCPTTR (26)..........................................................58

Testing the protection without external temperature

compensation (NonComp)............................................................58
Completing the test.......................................................................59

Breaker failure protection, phase segregated activation and

output CCRBRF (50BF).....................................................................59

Checking the phase current operate value,

Pickup_PH............... 60

Checking the residual (ground fault) current operate value

Pickup_N set below Pickup_PH....................................................60
Checking the re-trip and back-up times........................................60
Verifying the re-trip mode............................................................. 61
Verifying the back-up trip mode....................................................62
Verifying the case

RetripMode = Contact.....................................63

Verifying the function mode

Current&Contact.............................. 63

Completing the test.......................................................................64

Breaker failure protection, phase segregated activation and

output CSPRBRF (50BF)...................................................................64

Checking the phase current operate value, Pickup_PH............... 65
Checking the residual (GF) current operate value

IN> set

below IP>......................................................................................65
Checking the re-trip and back-up times........................................65
Verifying the

RetripMode..............................................................66

Verifying the case

RetripMode = No CB Pos Check.................... 67

Verifying the function mode

Current&Contact.............................. 67

Checking the case with fault current below set value

Pickup_

BlkCont.........................................................................................67
Checking the phase current operate value,

Pickup_PH............... 68

Completing the test.......................................................................68

Stub protection STBPTOC (50STB).................................................. 68

Measuring the operate limit of set values.....................................69
Completing the test.......................................................................69

Pole discrepancy protection CCRPLD (52PD).................................. 70

Verifying the settings.................................................................... 70
Completing the test.......................................................................70

Broken conductor check BRCPTOC (46).......................................... 70

Measuring the operate and time limit of set values...................... 71

Table of contents

Commissioning manual

Содержание Relion REQ650






















































































































































Результаты поиска

Содержание Relion REQ650

Отзывы:

Бренды по названию

Популярные бренды

ABB Relion REQ650, Руководство по вводу в эксплуатацию

Результаты поиска

Содержание Relion REQ650

Отзывы:

Бренды по названию

Популярные бренды