ABB Relion REQ650 Скачать руководство пользователя страница 66

Страница: 66 / 150

Inject a voltage 0.8 ·

VNRelPU

and a current high enough to operate the directional

function at the chosen angle.

Increase the voltage until the directional function is released.

Compare the measured value with the set

VNRelPU

operate value.

6.3.7.2

Completing the test

Continue to test another function or end the testing by setting the parameter

TestMode

Disabled

under

Main menu/Tests/IED test mode/TESTMODE:1

. If another function is

tested, then set the parameter

Blocked

under

Main menu/Tests/Function test

modes/Current/SDEPSDE(67N,IN<->)/SDEPSDE:1

for the function, or for each

individual function in a chain, to be tested next. Remember to set the parameter

Blocked

Yes

, for each individual function that has been tested.

6.3.8

Thermal overload protection, one time constant, Fahrenheit/

Celsius LFPTTR/LCPTTR (26)

Prepare the IED for verification of settings as outlined in

5.1 "Preparing the IED to verify

settings"

Values of the logical signals for LFPTTR/LCPTTR (26) are available on the local HMI
under ,

Main menu/Tests/Function status/Current/LFPTTR(26,T>)/LFPTTR:1

Main menu/Tests/Function status/Current/LCPTTR(26,T>)/LCPTTR:1

. The

Signal Monitoring in PCM600 shows the same signals that are available on the local HMI.

Check that the input logical signal BLOCK is logical zero and that on the local HMI, the
logical signal TRIP, PICKUP and ALARM are equal to logical zero.

6.3.8.1

Testing the protection without external temperature compensation

(NonComp)

Quickly set the measured current (fault current) in one phase to about 300% of

IRef

(to minimise the trip time), and switch the current off.

Reset the thermal memory on the local HMI under

Main menu/Clear/Clear

temperature constant/LFPTTR(26,8>)/LFPTTR:1

Main menu/Clear/Clear

temperature constant/LCPTTR(26,8>)/LCPTTR:1

Switch the fault current on and take note of the temperature, available on the local
HMI under

Main menu/Tests/Function status/Current/LFPTTR(26,8>)/

LFPTTR:1/Outputs/TEMP

Main menu/Tests/Function status/Current/

LCPTTR(26,8>)/LCPTTR:1/Outputs/TEMP

Check the time until the alarm limit has reached the

AlarmTemp

level during

injection.

Section 6

1MRK 505 293-UUS A

Testing functionality

Commissioning manual

Содержание Relion REQ650






















































































































































Результаты поиска

Содержание Relion REQ650

Отзывы:

Бренды по названию

Популярные бренды

ABB Relion REQ650, Руководство по вводу в эксплуатацию

Результаты поиска

Содержание Relion REQ650

Отзывы:

Бренды по названию

Популярные бренды