manualshive.com logo in svg

ABB Relion REQ650, Руководство по вводу в эксплуатацию

Поделиться
Скачать
ABB Relion REQ650 Скачать руководство пользователя страница 71

1.

Set 

BuTripMode

 = 

2 out of 4

.

2.

Apply the fault condition, including initiation of CCRBRF (50BF), with one-phase
current above set 

Pickup_PH

 and residual (ground fault) above set 

Pickup_N

.

3.

Verify that back-up trip is achieved after set time. If selected, re-trip should also
appear.

4.

Apply the fault condition, including initiation of CCRBRF (50BF), with at least one-
phase current below set 

Pickup_PH

 and residual (ground fault) above set 

Pickup_N

.

The current may be arranged by feeding three- (or two-) phase currents with equal
phase angle (I0-component) below 

Pickup_PH

, but of such value that the residual

(ground fault) current (3I

0

) will be above set value 

Pickup_N

.

5.

Verify that back-up trip is not achieved.

6.

Disconnect AC and INITIATE input signals.

6.3.9.6 

Verifying the case 

RetripMode = Contact

It is assumed that re-trip without current check is selected, 

RetripMode

 = 

Contact

.

1.

Set 

FunctionMode

 = 

Contact

2.

Apply input signal for CB closed to input 52a_A (B or C).

3.

Apply input signal, for initiation of CCRBRF (50BF).

4.

Verify that phase selection re-trip and back-up trip are achieved after set times.

5.

Disconnect the trip signal. Keep the CB closed signal.

6.

Apply input signal, for initiation of CCRBRF (50BF).

7.

Arrange disconnection of CB closed signal well before set back-up trip time 

t2

.

8.

Verify that back-up trip is not achieved.

9.

Disconnect injected AC and INITIATE input signals.

6.3.9.7 

Verifying the function mode 

Current&Contact

To be made only when 

FunctionMode

 = 

Current&Contact

 is selected.

Checking the case with fault current above set value 

Pickup_PH

The operation shall be as in 

FunctionMode

 = 

Current

.

1.

Set 

FunctionMode

 = 

Current&Contact

.

2.

Leave the inputs for CB close inactivated. These signals should not influence.

3.

Apply the fault condition, including initiation of CCRBRF (50BF), with current
above the set 

Pickup_PH

 value.

4.

Check that the re-trip, if selected, and back-up trip commands are achieved.

5.

Disconnect injected AC and INITIATE input signals.

1MRK 505 293-UUS A

Section 6

Testing functionality

63

Commissioning manual

Содержание Relion REQ650























































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды