manualshive.com logo in svg

ABB Relion REQ650, Руководство по вводу в эксплуатацию

Поделиться
Скачать
ABB Relion REQ650 Скачать руководство пользователя страница 125

Redundant communication according to IEC62439–3 Edition 1 and IEC
61850–9–2LE process bus communication are not supported in the 650
Ver 1.3 series IEDs.

6.11.1.2 

Setting the station communication

To enable the IEC 61850 communication, the corresponding COM03 ports must be
activated. Port LAN1 A and LAN1 B are used for redundancy.

If COM03 is used; the following below apply. If COM05 is used; there is no redundancy
and the port is named LAN1 or (FRONT)

To enable IEC 61850 station communication:

•

The IEC 61850-8-1 station communication functionality must be configured in the
local HMI. Navigate to 

Main Menu/Configuration/Communication/TCP-IP

configuation/ETHLAN1_AB

 and set the 

OperationMode

 parameter to

NonRedundant(A) 

or, for redundant communication, to 

PRP(A+B)

.

•

To enable GOOSE communication, the 

Operation

 parameter for the corresponding

GOOSE function blocks (GOOSEBINRCV and GOOSEINTLKRCV) must be set to

Enabled

 in the application configuration.

•

To enable GOOSE communication via the front port the parameter 

GOOSE

 in 

Main

menu/Configuration/Communication/Station communication/IEC61850-8-1/
PortSelGOOSE

 must be set to 

Front

. To enable GOOSE communication via rear

port the parameter 

PortSelGOOSE

 must be set to 

LAN1

.

To enable IEC 61850 station communication:

1.

Enable IEC 61850-8-1 (substation bus) communication for port A and B.
1.1. Set values for ETHLAN1_AB.

Navigate to 

Main Menu/Configuration/TCP-IP configuation/

ETHLAN1_AB

.

Set values for 

OperationMode

, 

IPAddress

 and 

IPMask

. 

OperationMode

 must

be set to 

NonRedundantA

.

Check that the correct IP address is assigned to the port.

1.2. Enable IEC 61850-8-1 communication.

Navigate to 

Main menu/Settings/General settings/Communication/

Station communication/IEC 61850-8-1

.

Set 

Operation

 to 

Enabled

 and 

PortSelGOOSE

 to the port used.

2.

Enable redundant IEC 61850-8-1 communication for port A and B.
2.1. Enable redundant communication.

1MRK 505 293-UUS A

Section 6

Testing functionality

117

Commissioning manual

Содержание Relion REQ650























































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды