manualshive.com logo in svg

ABB Relion REQ650, Руководство по вводу в эксплуатацию

Поделиться
Скачать
ABB Relion REQ650 Скачать руководство пользователя страница 107

1.

Verify the settings 

AutoEnerg

 or 

ManEnerg

 to be 

DBLL

.

2.

Apply a single-phase voltage of 30% 

GblBaseSelBus

 to the V-Bus and a single-

phase voltage of 100% 

GblBaseSelLine

 to the V-Line.

3.

Check that the AUTOENOK and MANENOK outputs are activated after set

tAutoEnerg

 respectively 

tManEnerg

.

4.

Decrease the V-Line to 60% 

GblBaseSelLine

 and keep the V-Bus equal to 30%

GblBaseSelBus

. The outputs should not be activated.

5.

The test can be repeated with different values on the V-Bus and the V-Line.

Testing both directions (DLLB or DBLL)

1.

Verify the local HMI settings 

AutoEnerg

 or 

ManEnerg

 to be 

Both

.

2.

Apply a single-phase voltage of 30% 

GblBaseSelLine

 to the V-Line and a single-

phase voltage of 100% 

GblBaseSelBus

 to the V-Bus.

3.

Check that the AUTOENOK and MANENOK outputs are activated after set

tAutoEnerg

 respectively 

tManEnerg

.

4.

Change the connection so that the V-Line is equal to100% 

GblBaseSelLine

 and the

V-Bus is equal to 30% 

GblBaseSelBus

. The outputs should still be activated.

5.

The test can be repeated with different values on the V-Bus and the V-Line.

Testing the dead bus dead line (DBDL)

The test should verify that the energizing check function operates for a low voltage on both
the V-Bus and the V-Line, that is, closing of the breaker in a non-energized system. Test
is valid only when this function is used.

1.

Verify the local HMI setting 

AutoEnerg

 to be 

Disabled

 and 

ManEnerg

 to be 

DBLL

.

2.

Set the parameter 

ManEnergDBDL

 to 

Enabled

.

3.

Apply a single-phase voltage of 30% 

GblBaseSelBus

 to the V-Bus and a single-

phase voltage of 30% 

GblBaseSelLine

 to the V-Line.

4.

Check that the MANENOK output is activated after set 

tManEnerg

.

5.

Increase the V-Bus to 80% 

GblBaseSelBus

 and keep the V-Line equal to 30%

GblBaseSelLine

. The outputs should not be activated.

6.

Repeat the test with 

ManEnerg

 set to 

DLLB

 with different values on the V-Bus and

the V-Line voltage.

6.7.1.4 

Testing the voltage selection

Testing the voltage selection for single CB arrangements

This test should verify that the correct voltage is selected for the measurement in the
SESRSYN function used in a double-bus arrangement. Apply a single-phase voltage of

1MRK 505 293-UUS A

Section 6

Testing functionality

99

Commissioning manual

Содержание Relion REQ650























































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды