manualshive.com logo in svg

ABB Relion REQ650, Руководство по вводу в эксплуатацию

Поделиться
Скачать
ABB Relion REQ650 Скачать руководство пользователя страница 77

Values of the logical signals for STBPTOC (50STB) are available on the local HMI under

Main menu/Tests/Function status/Current/STBPTOC(50STB,I>)/STBPTOC:1

.

The Signal Monitoring in PCM600 shows the same signals that are available on the local
HMI.

6.3.11.1 

Measuring the operate limit of set values

1.

Check that the input logical signals BLOCK and ENABLE and the output logical
signal TRIP are all logical zero.

2.

Activate the input ENABLE on the STBPTOC (50STB) function block

3.

For a short while inject a current (fault current) in one phase to about 110% of the set
operating current, and switch the current off.
Observe to not exceed the maximum permitted overloading of the current circuits in
the IED.

4.

Switch the fault current on and measure the operating time of STBPTOC (50STB).
Use the TRIP signal from the configured binary output to stop the timer. The
operation should be instantaneously.

5.

Activate the input BLOCK on the STBPTOC (50STB) function block.

6.

Switch on the fault current (110% of the setting).
No TRIP signal should appear.

7.

Switch off the fault current.

8.

For a short while inject a current (fault current) in same phase to about 90% of the
set operating current, and switch the current off.

9.

Switch the fault current on.
No TRIP signal should appear.

10. Switch off the fault current.
11. Reset the ENABLE binary input.
12. Switch the fault current on.

No TRIP signal should appear.

13. Disable the fault current.

6.3.11.2 

Completing the test

Continue to test another function or end the testing by setting the parameter 

TestMode

 to

Disabled

 under 

Main menu/Tests/IED test mode/TESTMODE:1

. If another function is

tested, then set the parameter 

Blocked

 to 

No

 under 

Main menu/Tests/Function test

modes/Current/STBPTOC(50STB,I>)/STBPTOC:1

 for the function, or for each

individual function in a chain, to be tested next. Remember to set the parameter 

Blocked

 to

Yes

, for each individual function that has been tested.

1MRK 505 293-UUS A

Section 6

Testing functionality

69

Commissioning manual

Содержание Relion REQ650























































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды