manualshive.com logo in svg

ABB Relion REQ650, Руководство по вводу в эксплуатацию

Поделиться
Скачать
ABB Relion REQ650 Скачать руководство пользователя страница 57

Verification of the non-directional phase overcurrent function is
done as instructed above, without applying any polarizing voltage.

6.3.3.2 

Completing the test

Continue to test another function or end the testing by setting the parameter 

TestMode

 to

Disabled

 under 

Main menu/Tests/IED test mode/TESTMODE:1

. If another function is

tested, then set the parameter 

Blocked

 to 

No

 under 

Main menu/Tests/Function test

modes/Current/OC4PTOC(51_67,4I>)/OC4PTOC:1

 for the function, or for each

individual function in a chain, to be tested next. Remember to set the parameter 

Blocked

 to

Yes

, for each individual function that has been tested.

6.3.4 

Four step phase overcurrent protection phase segregated

output OC4SPTOC (51_67)

Prepare the IED for verification of settings as outlined in 

5.1 "Preparing the IED to verify

settings"

.

Values of the logical signals for OC4SPTOC (51_67) are available on the local HMI under

Main menu/Tests/Function status/Current/OC4SPTOC(51_67,4I>)/OC4SPTOC:1

.

The Signal Monitoring in PCM600 shows the same signals that are available on the local
HMI.

6.3.4.1 

Verifying the settings

1. Connect the test set for appropriate current injection to the appropriate IED phases.

If there is any configuration logic that is used to enable/block any of the four available
overcurrent steps, make sure that the step under test is enabled, for example end fault
protection. Connect the symmetrical three-phase injection current into phases A, B
and C.

2. Connect the test set for the appropriate three-phase voltage injection to the IED

phases A, B and C.
Make sure that the protection is fed with a symmetrical three-phase voltage.

3. Set the injected polarizing voltage slightly larger than the set minimum polarizing

voltage (default is 5% of 

VBase

) and set the injection current to lag the appropriate

voltage by an angle of about 55° if forward directional function is selected.
If reverse directional function is selected, set the injection current to lag the polarizing
voltage by an angle equal to 235° (equal to 55° + 180°).

4. Increase the injected current and note the operated value of the tested step of the

function.

5. Decrease the current slowly and note the reset value.

1MRK 505 293-UUS A

Section 6

Testing functionality

49

Commissioning manual

Содержание Relion REQ650























































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды