ABB Relion REQ650 Скачать руководство пользователя страница 70

Страница: 70 / 150

Apply the fault condition, including initiation of CCRBRF (50BF), with current
below set current value.

Verify that re-trip is achieved after set time

, but no back-up trip is obtained.

Disconnect AC and INITIATE input signals.

6.3.9.5

Verifying the back-up trip mode

In the cases below it is assumed that

FunctionMode

Current

is selected.

Checking that back-up tripping is not achieved at normal CB tripping

Use the actual tripping modes. The case below applies to re-trip with current check.

Apply the fault condition, including initiation of CCRBRF (50BF), with phase
current well above set value

Interrupt the current, with a margin before back-up trip time,

. It may be made at

issue of re-trip command.

Check that re-trip is achieved, if selected, but no back-up trip is obtained.

Disconnect AC and INITIATE input signals.

The normal mode

BuTripMode

1 out of 3

should have been verified in the tests above.

In applicable cases the modes

1 out of 4

and

2 out of 4

can be checked. Choose the mode

below, which corresponds to the actual case.

Checking the case

BuTripMode = 1 out of 4

It is assumed that the ground-fault current setting

Pickup_N

is below phase current setting

Pickup_PH

Set

BuTripMode

1 out of 4

Apply the fault condition, including initiation of CCRBRF (50BF), with one-phase
current below set

Pickup_PH

but above

Pickup_N

. The residual ground-fault should

then be above set

Pickup_N

Verify that back-up trip is achieved after set time. If selected, re-trip should also
appear.

Disconnect AC and INITIATE input signals.

Checking the case

BuTripMode = 2 out of 4

The ground-fault current setting

Pickup_N

may be equal to or below phase-current setting

Pickup_PH

Section 6

1MRK 505 293-UUS A

Testing functionality

Commissioning manual

Содержание Relion REQ650






















































































































































Результаты поиска

Содержание Relion REQ650

Отзывы:

Бренды по названию

Популярные бренды

ABB Relion REQ650, Руководство по вводу в эксплуатацию

Результаты поиска

Содержание Relion REQ650

Отзывы:

Бренды по названию

Популярные бренды