manualshive.com logo in svg

ABB Relion REQ650, Руководство по вводу в эксплуатацию

Поделиться
Скачать
ABB Relion REQ650 Скачать руководство пользователя страница 78

6.3.12 

Pole discrepancy protection CCRPLD (52PD)

Prepare the IED for verification of settings as outlined in 

5.1 "Preparing the IED to verify

settings"

.

Values of the logical signals for CCRPLD (52PD) are available on the local HMI under

Main menu/Tests/Function status/Current/CCRPLD(52PD)/CCRPLD:X

. The

Signal Monitoring in PCM600 shows the same signals that are available on the local HMI.

6.3.12.1 

Verifying the settings

1.

When CCRPLD (52PD) is set for external, set setting 

ContSel

 to 

Enable

 under 

Main

menu/Settings/IED Settings/Current/CCRPLD/CCRPLD:1

 to activate the logic

that detects pole discordance when external pole discordance signaling is used (input
EXTPDIND) in the application configuration.

2.

Activate the input EXTPDIND on CCRPLD (52PD) function block, and measure
the operating time of CCRPLD (52PD).

3.

Compare the measured time with the set value 

tTrip

.

4.

Reset the EXTPDIND input.

5.

When CCRPLD (52PD) is set for unsymmetrical current detection with CB
monitoring, set setting 

CurrSel

 under 

Main menu/Settings/IED Settings/Current/

CCRPLD/CCRPLD:1

 to 

Enable

.

Use the TRIP signal from the configured binary output to stop the timer.

6.

Repeat point 4 and 5 using OPENCMD instead of CLOSECMD. Set all three
currents to 110% of 

CurrRelLevel

. Activate CLOSECMD.

NO TRIP signal should appear due to symmetrical condition.

6.3.12.2 

Completing the test

Continue to test another function or end the testing by setting the parameter 

TestMode

 to

Disabled

 under 

Main menu/Tests/IED test mode/TESTMODE:1

. If another function is

tested, then set the parameter 

Blocked

 to 

No

 under 

Main menu/Tests/Function test

modes/Current/CCRPLD(52PD)/CCRPLD:X

 for the function, or for each individual

function in a chain, to be tested next. Remember to set the parameter 

Blocked

 to 

Yes

, for

each individual function that has been tested.

6.3.13 

Broken conductor check BRCPTOC (46)

Prepare the IED for verification of settings as outlined in 

5.1 "Preparing the IED to verify

settings"

.

Section 6

1MRK 505 293-UUS A

Testing functionality

70

Commissioning manual

Содержание Relion REQ650























































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды