ABB IRB 390 Скачать руководство пользователя

Страница: 50 / 346

3.3.4 Securing the robot frame

General

This section specifies the requirements for the robot frame installation.

Requirements on robot frame fastening

The fastening of the robot frame to the foundation must withstand the operational
loads. See

Loads on foundation, robot on page 37

The requirements for the robot foundation, that is the robot anchoring points on
the robot frame, must be met. See

Requirements, foundation on page 38

WARNING

The robot frame must be secured before mounting the robot.

Required equipment

Note

Spare part no.

Equipment

Standard toolkit on page 336

Standard tools

Orienting and securing

Note

Action

Make sure the installation site for the robot con-
forms to the specifications in section

Technical data

on page 37

See

Minimum required free space

above the robot on page 49

Make sure that the space above the installation site
is sufficient for repair and maintenance.

Prepare the installation site.

Use fastening bolts that withstand
the requirements for current
foundation.

Secure the robot frame to the floor.

Note

Use leveling shims if needed.

See

Requirements, foundation on

page 38

Make sure the robot anchoring points are level after
having installed and secured the frame to the
floor/foundation.

See

Illustration of leveling the ro-

bot frame on page 51

Continues on next page

Product manual - IRB 390

3HAC066566-001 Revision: B

3 Installation and commissioning

3.3.4 Securing the robot frame

Содержание IRB 390



























































































































































































































































































































































Результаты поиска

Содержание IRB 390

Отзывы:

Похожие инструкции для IRB 390

Бренды по названию

Популярные бренды

ABB IRB 390, Руководство по эксплуатации продукта

Результаты поиска

Содержание IRB 390

Отзывы:

Похожие инструкции для IRB 390

Бренды по названию

Популярные бренды