ABB IRB 390 Скачать руководство пользователя

Страница: 216 / 346

Note

Action

Universal joint: 3HAC059503-001

Fit the sealing ring and the new joint.

Sealing ring: 3HAC060263-001.

Lubricate the screw thread and the washer surface
underneath the screw head.

Torque wrench head, closed end:
3HAC063379-001.

Secure with the lubricated screws and washers
and tighten, using a special torque wrench head. Hexagon flange bolt: 3HAC058625-

001

Hold the motor shaft still with an open-end wrench
(47 mm) at the joint while tightening the screws.
Requires two persons.

Note

Replace the washers with new, for hygienic pur-
pose, if the rubber is damaged.

Washer: M8 hygienic
(3HAC058626-004)
Anti-seize paste: Molykote P1900
(3HAC070875-002)
Tightening torque: 35 Nm.

xx1900001827

xx2000001061

Refitting the telescopic shaft

Use these procedures to refit the telescopic shaft.

Refitting the upper end of the telescopic shaft

Note

Action

Cleaning agent: Isopropanol.

Clean the friction shim, the sealing ring and the
contact surfaces with isopropanol. Inspect for
damage.

Friction shim: 3HAC060200-001.
Sealing ring: 3HAC060263-001

Replace if damaged.

Continues on next page

216

Product manual - IRB 390

3HAC066566-001 Revision: B

5 Repair

5.5.3 Replacing the telescopic shafts and universal joints

Continued

Содержание IRB 390



























































































































































































































































































































































Результаты поиска

Содержание IRB 390

Отзывы:

Похожие инструкции для IRB 390

Бренды по названию

Популярные бренды

ABB IRB 390, Руководство по эксплуатации продукта

Результаты поиска

Содержание IRB 390

Отзывы:

Похожие инструкции для IRB 390

Бренды по названию

Популярные бренды