ABB DCS550 Series, Руководство пользователя

Страница: 243 / 316

243
Signal and parameter list
3ADW000379R0501 DCS550 Manual e e
Signal / Parameter name
m
in.
ma
x.
def
.
uni
t
dt
d
J T
acc
ω
*
=
J
mot
, J
gearbox
, J
spool
= J
mech
= const.
J
coil
~ D
4
T
acc
[Nm] torque needed for acceleration
J [kg m
2
] inertia of the complete winder
dÉ / dt [1/s
2
] angular acceleration
The inertia compensation calculates the acceleration torque needed to compensate the inertia of the winder mechanics
plus the inertia of the coil. To adapt the inertia of the coil its diameter and width is needed.
Commissioning hint:
−
InerMech (62.26) has to be determined by means of acceleration trials with maximum acceleration using the shortest
ramp time. Only the spool is on the winder. The result is available in MotTorqFilt (1.07) during the acceleration.
Autotuning is possible with WinderTuning (61.21) = InerMechComp.
−
InerCoil (62.25) has to be determined by means of acceleration trials with maximum acceleration using the shortest
ramp time. The largest coil (maximum diameter and maximum width) has to be on the winder. The result is available in
MotTorqFilt (1.07) during the acceleration.
Autotuning is possible with WinderTuning (61.21) = InerCoilComp.
−
Do not forget to subtract the average friction losses from the measured values - see FrictAt0Spd (63.26) to
FrictAt100Spd (63.30).
−
The width calculation works with relative width’ in percent of the maximum width, so the physical values must be
converted.
% 100 * ) 27 . 62 (
max
Width
Width
dth InerCoilWi
act
=
−
InerReleaseCmd (62.28) releases InertiaComp (62.30). The output is forced to zero if the switch is open.
62.23 InerDiaActIn (inertia compensation, actual diameter input)
Source (signal/parameter) for the actual diameter input of the inertia compensation. The format is xxyy, with:
xx = group and yy = index.
Default setting of 6208 equals DiameterAct (62.08).
Int. Scaling: 1 == 1
Type: I Volatile: N
0 9999 6208 -
62.24 InerAccActIn (inertia compensation, actual acceleration input)
Source (signal/parameter) for the actual acceleration input of the inertia compensation. The format is -xxyy,
with: - = negate input, xx = group and yy = index.
Default setting of 6221 equals AccActAdjust (62.21).
Int. Scaling: 1 == 1
Type: SI Volatile: N
-9999 9999 6221 -
62.25 InerCoil (inertia compensation, coil inertia)
Acceleration torque for the inertia of the coil in percent of MotNomTorque (4.23). Acceleration trials have to be
done with the largest (maximum diameter and maximum width) coil available.
Int. Scaling: 100 == 1 % Type: I
Volatile: N
0 100 0 %
62.26 InerMech (inertia compensation, mechanics inertia)
Acceleration torque for the inertia of the winder mechanics in percent of MotNomTorque (4.23). Acceleration
trials have to be done with an empty spindle or empty spool.
Int. Scaling: 100 == 1 % Type: I
Volatile: N
0 100 0 %
J
mot
J
gearbox
J
coil
J
spool
J
mot
J
gearbox
J
coil
J
spool