Aanderaa DCPS 5400 Скачать руководство пользователя страница 57

Страница: 57 / 150

July 2019 – TD 304 OPERATING MANUAL – Doppler Current Profiler Sensor

Page 57

2.5

User Maintenance settings

Under

User Maintenance

, you find

properties that are password protected

and are set / altered by a trained user. It

is not recommended to change

properties unless instructed. To access

these, check the “

Include User

Maintenance”

box in the device

configuration before clicking on the

“Get

Current Configuration…

” button. The

password is:

1000

. The user

maintenance settings are accessible by

clicking the “

Edit

…” button under

User

Maintenance

(refer to

Figure 2-8

Figure 2-35: User maintenance

2.5.1

Mandatory

Figure 2-36: Mandatory

All sensors are given a

Node Description

text like DCPS #xxx (xxx is the serial number of the sensor). The user can

modify this node description text if required. Be aware that the node description changes to *Corrupt Configuration if it

has lost the configuration in flash. Contact the factory if this happens. The configuration is saved in two sectors in flash

memory. A flash sector can be corrupted if the power is lost during the saving of new configuration. The double flash

sector saving ensures that it does not lose the configuration. If one of the sectors is corrupted, the other sector is used

and also saved to the corrupt sector.

Содержание DCPS 5400























































































































































Результаты поиска

Содержание DCPS 5400

Отзывы:

Похожие инструкции для DCPS 5400

Бренды по названию

Популярные бренды

Aanderaa DCPS 5400, Руководство по эксплуатации

Результаты поиска

Содержание DCPS 5400

Отзывы:

Похожие инструкции для DCPS 5400

Бренды по названию

Популярные бренды