Aanderaa DCPS 5400 Скачать руководство пользователя страница 31

Страница: 31 / 150

July 2019 – TD 304 OPERATING MANUAL – Doppler Current Profiler Sensor

Page 31

1.7.4 User Maintenance

This group contains sensor settings that normally are not altered by the user. To access most of these properties you

need to send passkey(1000) or with Real-Time Collector use password: 1000. These properties are used to configure

serial port settings, communication to and from sensor. If you got a wave license key you may also enable wave

functionality, you may enter temperature coefficients if Temperature sensor is included, set limits for discarding ping if

sensor tilt exceeds the limits and property to set the distance from pressure sensor port to centre of transducer

elements.

Table 1-8: Sensor properties for Doppler Current Profiler Sensor 5400/5400R, 5402/5402R and 5403/5403R

ENUM=Enumeration, INT =Integer, BOOL=Boolean (‘yes’/’no’)

Table 1-1
Property

Type

No of
e

lem

ent

Use

Conf

igur

ation

tegor

Acces
s

Pro

cti

d/W

rite

Node Description String 31 User text for describing node, placement etc.

No /

Low

Owner

String 31 User setting for owner information, company name etc.

No /

High

Interface

String 31 Factory use only, RS232 for standard version, RS422 for R-version

High

Baudrate

ENUM 1

RS232 baudrate: 4800, 9600, 57600, or 115200. Default baudrate

is 115200. The baudrate affects the minimum available Interval

setting.

Flow Control

ENUM 1

RS232/RS422 flow control: ‘None’ or ‘Xon/Xoff’. The Xon/Xoff’

characters are also sent for each Doppler ping measurement. To

remove the “disturbance” on the receiver, select None. Be aware

that this may also lead to missing characters when sending

commands to the sensor.

Enable Comm

Indicator

ENUM 1

Enable communication sleep (’%’) and communication ready (‘!’)

indicators. After the last communication with the sensor, it normally

outputs a ‘%’ when the Comm Timeout time is over. When a

character is sent to the sensor, it outputs a ‘!’ to indicate that it is

ready to communicate.

Comm TimeOut

BOOL 1

Time communication is active (Always On, 10 s, 20 s, 30 s, 1min, 2

min, 5 min, 10 min). A short time means that the sensor is going to

sleep faster after a communication input.

Enable Old Time

Setting

BOOL 1

Enables old input in Smart Sensor Terminal mode for Interval and

Polled pingrate.

Acoustic Wave

Product Number String 6

For factory use only.

Read

Only

Содержание DCPS 5400























































































































































Результаты поиска

Содержание DCPS 5400

Отзывы:

Похожие инструкции для DCPS 5400

Бренды по названию

Популярные бренды

Aanderaa DCPS 5400, Руководство по эксплуатации

Результаты поиска

Содержание DCPS 5400

Отзывы:

Похожие инструкции для DCPS 5400

Бренды по названию

Популярные бренды