Aanderaa DCPS 5400 Скачать руководство пользователя страница 70

Страница: 70 / 150

Page 70

July 2019 – TD 304 OPERATING MANUAL – Doppler Current Profiler Sensor

3.5.1

Site Info

Figure 3-16: Site Info

Site Info

containing four properties:

•

Location:

Name of location where the instrument is deployed.

•

Geographic Position:

GPS potion for deployment format Latitude, Longitude.

•

Vertical Position:

Position in water column, e.g. 5 meter depth.

•

Reference:

Free text for additional information.

All these settings are optional information to be entered to store information about the deployment. These setting are not

used in calculation.

Geographical Position

is used to give the map coordinates unless a GPS input is connected.

3.5.2

Orientation

Figure 3-17:Orientation

Enable Magnetic Declination

is normally used when sensor is used close to South Pole or North Pole.

Declination

Angle (Deg.M)

is a value to correct for the magnetic variation on the site where the sensor is used. This is the angle in

degrees between magnetic north and true north.

Magnetic declination (variation) is the angle between the magnetic

north and the true north. This angle varies depending on the position on the Earth’s surface and also varies over time.

Declination is positive when magnetic north is east of true north and negative when it is to the west (input angle value

±180°). Magnetic declination at the deployment location can be found for i.e. on NOAA website:

http://www.ngdc.noaa.gov/geomag-web/

Содержание DCPS 5400























































































































































Результаты поиска

Содержание DCPS 5400

Отзывы:

Похожие инструкции для DCPS 5400

Бренды по названию

Популярные бренды

Aanderaa DCPS 5400, Руководство по эксплуатации

Результаты поиска

Содержание DCPS 5400

Отзывы:

Похожие инструкции для DCPS 5400

Бренды по названию

Популярные бренды