Aanderaa DCPS 5400 Скачать руководство пользователя страница 51

Страница: 51 / 150

July 2019 – TD 304 OPERATING MANUAL – Doppler Current Profiler Sensor

Page 51

2.4.9

Output enabling – Profile Parameters

Figure 2-30: Output – Profile Parameters

While configuring the sensor, it is possible to define which parameters should be calculated and sent from the sensor.

Select Profile Parameters

gives the user the choice to either select one of the predefined groups of Profile Parameter

or you might select your own selection

in User Specified – Profile Parameters

refer chapter

2.4.10

, by selecting

User

Specified

. The sensor always outputs the

Cell State1

Cell State2

Horizontal Speed

and

Direction

for all the cells

(not possible to disable). Available settings for

Select Profile Parameters

are:

•

Simple Output

•

Basic Output

•

Basic + Beam Output

•

Basic + 3-Beam Output

•

Basic + Beam + 3-Beam Output

•

Full Output

•

User Specified

Refer

Table 2-1

for parameters included in each group.

Refer to

Table 1-5

for definition of the parameters.

NOTE: Enabling more data also means larger data messages and more time to transfer data.
All profile parameters are an average of each ping data from the last measurement interval.

Enable 4-Beam Auto Replacement.

If selected all 4-beam parameters will automatically be replaced with the best 3-

beam solution if a disturbance is detected in one of the beam.

Содержание DCPS 5400























































































































































Результаты поиска

Содержание DCPS 5400

Отзывы:

Похожие инструкции для DCPS 5400

Бренды по названию

Популярные бренды

Aanderaa DCPS 5400, Руководство по эксплуатации

Результаты поиска

Содержание DCPS 5400

Отзывы:

Похожие инструкции для DCPS 5400

Бренды по названию

Популярные бренды