Aanderaa DCPS 5400 Скачать руководство пользователя страница 105

Страница: 105 / 150

July 2019 – TD 304 OPERATING MANUAL – Doppler Current Profiler Sensor

Page 105

Some properties are passkey protected and will not be accessible without first writing the passkey. If the passkey is

needed you get the error message:

“ERROR PROTECTED PROPERTY”.

Using passkey 1000 opens up all user

accessible property settings.

5.5.5

XML commands

The

Get ConfigXML

command outputs all available sensor properties in XML-format.

The

Get DataXML

command outputs all available sensor parameters in XML-format.

The

XML-output

is a general format shared by all Aanderaa smart sensors; the output from different types of smart

sensors can be read and presented as e.g. in a general smart sensor setup program.

5.5.6

Examples – How to configure sensor in Smart Sensor Terminal mode

Use a terminal program e.g. Tera Term or Hyperterminal, refer chapter 3.3 for communication setup.

In the following examples several configuration changes are shown. The command

Stop

is recommended to avoid

output strings while configuring the sensor. If the sensor has started to transmit data when the user tries to

communicate, it may take a while before the command response is sent from the sensor. This depends on the number

of enabled cells and output parameters etc.

Example 1: Configure 1 column, the other columns disabled

//Press Enter to start communicating with the sensor, refer chapter

5.4

↵

//press Enter

Stop

↵

//Wait for ack #. Repeat if necessary

Set Passkey(1)

↵

Set C1 Enable Surface Reference(No)

↵

//wait for ack #

Set C1 Distance First Cell Center(6.0m)

↵

//wait for ack #

Set C1 Cell Size(2.0m) )

↵

//wait for ack #

Set C1 Number Of Cells(25)

↵

//wait for ack #

Set C1 Cell Center Spacing(2.0m))

↵

//wait for ack #

Set C2 Enable Column(No)

↵

//wait for ack #

Set C3 Enable Column(No)

↵

//wait for ack #

Set Enable Surface Cell(No)

↵

//wait for ack #

Do Refresh

↵

//necessary if column settings or ping number is changed before the interval

Set Interval(1 min)

//an error message is sent from the sensor if the interval is too short

Save

↵

// wait for ack #

Reset

↵

// the sensor will restart with new settings

Comments to example 1:

It is possible to enable the

Surface Cell

and also the

Surface Reference

for the column, but this requires that the

sensor knows the correct pressure. The automatic surface referencing was made for the SeaGuardII and SmartGuard

where the DCPS can receive the pressure measured directly from the Datalogger via AiCaP(as parameter input from a

pressure sensor connected to the same SeaGuardII/SmartGuard).

To use

Surface Reference

on a sensor without a SeaGuardII /SmartGuard with a pressure sensor connected, the user

has to set the correct

Fixed Installation Pressure

setting (can be changed while sensor is running).

Содержание DCPS 5400























































































































































Результаты поиска

Содержание DCPS 5400

Отзывы:

Похожие инструкции для DCPS 5400

Бренды по названию

Популярные бренды

Aanderaa DCPS 5400, Руководство по эксплуатации

Результаты поиска

Содержание DCPS 5400

Отзывы:

Похожие инструкции для DCPS 5400

Бренды по названию

Популярные бренды