Aanderaa DCPS 5400 Скачать руководство пользователя страница 20

Страница: 20 / 150

Page 20

July 2019 – TD 304 OPERATING MANUAL – Doppler Current Profiler Sensor

1.7.2 Deployment Settings

Deployment Settings contains settings for instruments metadata like position and owner, but also site dependent

properties storing data that might influence the measurement. Value stored in these setting can be used as default

values but might also be exchanged with real-time measured data if sensors are connected to the AiCaP bus.

Table 1-6: Sensor properties for Doppler Current Profiler Sensor 5400/5400R, 5402/5402R, and 5403/5403R

ENUM=Enumeration, INT =Integer, BOOL=Boolean (‘yes’/’no’)

Table 1-1
Property

Type

No of
e

lem

ent

Use

Conf

igur

ation

tegor

Acces
s

Pro

cti

d/W

rite

Interval

ENUM 1

Set the output interval in seconds, minutes or hours. Minimum

available interval is dependent on configuration (time to do all

ping measurements).

No /

Location

String 31 User setting for location

Geographic Position String 31 User setting for geographic position
Vertical Position

String 31 User setting for describing sensors vertical position/depth

Reference

String 31 User setting for describing sensor reference, user definable.

Enable Magnetic

Declination

BOOL 1 Enables use of magnetic declination angle input (see

Declination Angle for value used)

No /

Low

Declination Angle

Float

A value to correct for the magnetic variation on the site where

the sensor is used. This is the angle in degrees between

magnetic north and true north.

Sound Speed

Float

Fixed sound speed setting in m/s. This value is used for cell

positioning in the profile and for calculation of current speed

values. Variable sound speed values can be used while sensor

is running.

3)4)

Air Pressure

Float

The air pressure in kPa. The air pressure value is used when

calculating depth. Can be altered while sensor is running to

compensate for variable air pressure.

Local Gravity

Constant

Float

1 Gravity constant in m/s² used for calculation of depth.

Salinity

Float

Salinity in PSU used for calculation of density, sound speed and

depth. Can be altered while sensor is running to compensate for

variable salinity.

Fixed Installation

Pressure

Float

The pressure in kPa at the deployment site. Can be altered

while sensor is running to compensate for variable pressure.

This value is used for calculation of depth if the surface cell or

surface reference is enabled without parameter input from a

pressure sensor.

5)6)

Not recommended.

Содержание DCPS 5400























































































































































Результаты поиска

Содержание DCPS 5400

Отзывы:

Похожие инструкции для DCPS 5400

Бренды по названию

Популярные бренды

Aanderaa DCPS 5400, Руководство по эксплуатации

Результаты поиска

Содержание DCPS 5400

Отзывы:

Похожие инструкции для DCPS 5400

Бренды по названию

Популярные бренды