Aanderaa DCPS 5400 Скачать руководство пользователя страница 100

Страница: 100 / 150

Page 100

July 2019 – TD 304 OPERATING MANUAL – Doppler Current Profiler Sensor

5.3

Communication setup

Most terminal programs can be used for

Smart Sensor Terminal

communication with the sensor when connected to a

PC, e.g. Teraterm.

The following Smart Sensor Terminal setup should be used:

115200 Baud
8 Data bits
1 Stop bit
No Parity
Xon/Xoff Flow Control

IMPORTANT! The terminal program must send a Line Feed after each Carriage Return.

5.4

Sensor startup

When property

Enable Text

is set to

Yes

StartupInfo

is displayed at sensor power up or after

Reset

StartupInfo

contains information about

Product Number, Serial Number, Mode, Protocol Version

and

Config Version

(Refer to

Figure 5-2

After the first line it also outputs

Initializing

… to indicate that it is busy. When it is ready and has started it outputs

Started….

The initializing phase can take up to approx. 30s dependent on the configuration of the sensor.

Figure 5-2: Start up info: communication using Tera Term

In order to minimize the current drain the sensor normally enters a power down mode after each sampling; the sensor

can be awake by any characters on the Smart Sensor Terminal input, and will stay awake for a time set by the

Comm

TimeOut

property after receiving the last character.

If the property

Comm TimeOut

is set to other than

‘Always On’

the serial interface will not be activated after power-up (or the

Reset

command). Any character will activate the serial interface, but a Carriage Return (CR or CR+LF),

‘/’

‘;’

are often

preferred since these characters do not interfere with the command syntax. The serial interface will then be active until a

period of input inactivity specified by the

Comm TimeOut

value (10 s, 20 s, 30 s, 1 min, 2 min, 5 min,10 min). The

Communication Sleep Indicator

‘%’,

will be transmitted when the serial communication is deactivated, and the

Communication Ready Indicator, ‘!’

is outputted subsequent to activation (electronics require up to 500ms start up time).

When

Comm TimeOut

is set to ‘

Always On’

the communication (and microprocessor) will be kept active all time.

The

Communication Sleep Indicator ‘%’

and the

Communication Ready Indicator ‘!‘

are not followed by Carriage

Return and Line Feed.

Содержание DCPS 5400























































































































































Результаты поиска

Содержание DCPS 5400

Отзывы:

Похожие инструкции для DCPS 5400

Бренды по названию

Популярные бренды

Aanderaa DCPS 5400, Руководство по эксплуатации

Результаты поиска

Содержание DCPS 5400

Отзывы:

Похожие инструкции для DCPS 5400

Бренды по названию

Популярные бренды