Aanderaa DCPS 5400 Скачать руководство пользователя страница 120

Страница: 120 / 150

Page 120

July 2019 – TD 304 OPERATING MANUAL – Doppler Current Profiler Sensor

East AutoBeam[cm/s]

Set NE Speed Output(Off/Output) and Set AutoBeam Output(Off/Output)

From software version 8.2.1:Set AutoBeam Speed

Type(Polar/Rectangular/Polar+Rectangular/ Replace 4-Beam Data) and

Set AutoBeam Output(Off/Output) set to Rectangular and Output to be enabled

Vertical Beam123[cm/s]

Set Vertical Speed Output(Off/Output) and Set 3-Beam Combination Output(Off/Output)

(both set to output to be enabled).

This is changed from software version 8.2.1. From this version only Set 3-Beam

Combination Output(Off/Output) affects the output of this parameter

Vertical Beam124[cm/s]

Set Vertical Speed Output(Off/Output) and Set 3-Beam Combination Output(Off/Output)

(both set to output to be enabled).

This is changed from software version 8.2.1. From this version only Set 3-Beam

Combination Output(Off/Output) affects the output of this parameter

Vertical Beam134[cm/s]

Set Vertical Speed Output(Off/Output) and Set 3-Beam Combination Output(Off/Output)

(both set to output to be enabled).

This is changed from software version 8.2.1. From this version only Set 3-Beam

Combination Output(Off/Output) affects the output of this parameter

Vertical Beam234[cm/s]

Set Vertical Speed Output(Off/Output) and Set 3-Beam Combination Output(Off/Output)

(both set to output to be enabled).

This is changed from software version 8.2.1. From this version only Set 3-Beam

Combination Output(Off/Output) affects the output of this parameter

Vertical AutoBeam[cm/s]

Set NE Speed Output(Off/Output) and Set AutoBeam Output(Off/Output)

From software version 8.2.1:

Set AutoBeam Output(Off/Output) and and Set Vertical Speed Output(Off/Output)

Beam1 Speed[cm/s]

Set Beam Speed Output(Off/Output)

Beam2 Speed[cm/s]

Set Beam Speed Output(Off/Output)

Beam3 Speed[cm/s]

Set Beam Speed Output(Off/Output)

Beam4 Speed[cm/s]

Set Beam Speed Output(Off/Output)

Beam1 Strength[dB]

Set Beam Strength Output(Off/Output)

Beam2 Strength[dB]

Set Beam Strength Output(Off/Output)

Beam3 Strength[dB]

Set Beam Strength Output(Off/Output)

Beam4 Strength[dB]

Set Beam Strength Output(Off/Output)

Beam1 Stdev[cm/s]

Set Std Dev Beam Speed Output(Off/Output)

Beam2 Stdev[cm/s]

Set Std Dev Beam Speed Output(Off/Output)

Beam3 Stdev[cm/s]

Set Std Dev Beam Speed Output(Off/Output)

Beam4 Stdev[cm/s]

Set Std Dev Beam Speed Output(Off/Output)

Cross Difference[cm/s]

Set Cross Difference Output(Off/Output)

Beam1 Correlation

Factor[cm/s]

Set Bandwidth(Broadband)

Set Correlation Factor Output(Off/Output)

Beam2 Correlation

Factor[cm/s]

Set Bandwidth(Broadband)

Set Correlation Factor Output(Off/Output)

Beam3 Correlation

Factor[cm/s]

Set Bandwidth(Broadband)

Set Correlation Factor Output(Off/Output)

Beam4 Correlation

Factor[cm/s]

Set Bandwidth(Broadband)

Set Correlation Factor Output(Off/Output)

Содержание DCPS 5400























































































































































Результаты поиска

Содержание DCPS 5400

Отзывы:

Похожие инструкции для DCPS 5400

Бренды по названию

Популярные бренды

Aanderaa DCPS 5400, Руководство по эксплуатации

Результаты поиска

Содержание DCPS 5400

Отзывы:

Похожие инструкции для DCPS 5400

Бренды по названию

Популярные бренды