Aanderaa DCPS 5400 Скачать руководство пользователя страница 23

Страница: 23 / 150

July 2019 – TD 304 OPERATING MANUAL – Doppler Current Profiler Sensor

Page 23

1.7.3 System Configuration

This group is used to control the sensor via properties for configuring communication with logger, sensor setup and

parameter enabling and controlling the output from sensor. Some of the properties are only visible depending on the

mode selected or if the function is enabled or not. These properties will either be grey or not visible at all. The wave

properties are only visible if a license key is set.

Table 1-7: Sensor properties for Doppler Current Profiler Sensor 5400/5400R, 5402/5402R, and 5403/5403R

ENUM=Enumeration, INT =Integer, BOOL=Boolean (‘yes’/’no’)

Table 1-1
Property

Type

No of
e

lem

ent

Use

Conf

igur

ation

tegor

Acces
s P

rot

ect

ion

d/W

rite

Mode

ENUM 1

Sets the sensor operation mode (AiCaP, Smart Sensor Terminal and

AADI Real-Time). AiCaP is not available on the R-version (5400R) of

the sensor. Smart Sensor Terminal is an ASCII output when AADI Real-

Time is XML output.

No /

Low

Enable Sleep BOOL 1

Enables sleep mode in Smart Sensor Terminal and AADI Real-Time

operation to save power (In AiCaP the sensor always tries to sleep

when not busy).

Enable Polled

Mode

BOOL 1

Enables polled mode in Smart Sensor Terminal Mode. When set to ‘no’

(non-polled operation) the sensor will sample at the interval given by the

Interval property. When set to ‘yes’ the sensor will start to do ping

measurements at the selected Polled Pingrate. A Do Sample command

triggers the end calculations and output of data. A Do Output command

can be sent to repeat the output of the last calculated data.

Polled

Pingrate

ENUM 1

Selectable ping rate in Polled mode between 0.1 and 10.0 Hz. The

maximum ping rate is limited by the configuration, i.e. large profile with

many cells gives lower maximum available pingrate.

Default is 1 Hz.

No /

Enable Text

BOOL 1

Controls the insertion of descriptive text in Smart Sensor Terminal

mode, i.e. parameter names and units. Can be used to reduce message

size.

No /

Low

Enable

Decimalformat BOOL 1

Controls the use of decimal format in the output string in Smart Sensor

Terminal mode. Default is scientific format (exponential format).

Enable Tilt

Compensation BOOL 1

Tilt compensation is used for correct positioning of the beam cells in

each depth cell. It also compensates the Doppler speed measurements

for variable tilt to calculate correct speed components (North, East and

Vertical). Default enabled.

Enable Fixed

Heading

BOOL 1

Allows the user to deactivate the internal compass and set a fixed

heading value. This can be used if for example the sensor is standing

on a fixed platform where the earth magnetic field is disturbed.

Содержание DCPS 5400























































































































































Результаты поиска

Содержание DCPS 5400

Отзывы:

Похожие инструкции для DCPS 5400

Бренды по названию

Популярные бренды

Aanderaa DCPS 5400, Руководство по эксплуатации

Результаты поиска

Содержание DCPS 5400

Отзывы:

Похожие инструкции для DCPS 5400

Бренды по названию

Популярные бренды