Aanderaa DCPS 5400 Скачать руководство пользователя страница 36

Страница: 36 / 150

Page 36

July 2019 – TD 304 OPERATING MANUAL – Doppler Current Profiler Sensor

2.1.2

Control Panel

In the

Control Panel

window you will find two tabs,

Recorder Panel and Device Configuration

. Under

Recorder

Panel

you can start and stop recordings. If the recorder is running first click on the

Stop Recorder

as you are not

allowed to configure the sensor when recording. The recorder panel is dependent on the Sensor Mode. In

AADI Real-

Time

mode you may start and stop the recorder. For

AiCaP

and

Smart Sensor Terminal

you can only refresh the

status but not start the recording.

Under

Start Option

you can start sensor

immediately by

Start Now

. The

Start Delayed

option is not yet implemented.

In the

Timing

session you may select the

recording interval using

Fixed Interval

. The

available interval will be dependent on the

sensor configuration. If you change the

configuration it might cause a change in the

Fixed Interval

so we recommend always

checking the interval after configuration is

finished.

The

Script

is not yet implemented.

The sensor will output one recording every

interval.

Figure 2-7: Recorder Panel

Click on the Device Configuration tab to

continue and access the sensor property menus.
Under the

Device Configuration

tab click on

the

Get Current Configuration

... button in

order to receive the current configuration from

the sensor.
To include the

User Maintenance

settings tick

off the I

nclude User Maintenance

box before

clicking the

Get Current Configuration

…

button.

The settings in

User Maintenance

are protected

with a higher access level. To access this menu

you will need to enter a

password

. This

password is 1000

for all sensors.

Figure 2-8: Device configuration

Содержание DCPS 5400























































































































































Результаты поиска

Содержание DCPS 5400

Отзывы:

Похожие инструкции для DCPS 5400

Бренды по названию

Популярные бренды

Aanderaa DCPS 5400, Руководство по эксплуатации

Результаты поиска

Содержание DCPS 5400

Отзывы:

Похожие инструкции для DCPS 5400

Бренды по названию

Популярные бренды