A.O. Smith BFM - 100 Скачать руководство пользователя страница 39 | Manualshive

Страница: 39 / 74

background image

Instruction manual BFM

39

is

4

Conversion to a
different gas category

Caution

The conversion may only by carried out by an authorised installation

engineer.

If the appliance must operate on a family of gases (LP gas or natural gas) or
other gas category than that for which the appliance has been set at the
factory, the appliance will have be adapted using a special conversion kit.

Caution

You must check the supply pressure and burner pressure once the

conversion is complete.

4.1

Conversion

1. Isolate

(10.3 "Isolating the appliance from the mains")

the water heater from

the power supply.

2. Shut off the gas supply.
3. Referring to the gas table

(3.4.3 "Gas data")

, determine whether the pilot

flame orifice for the intended gas category is different from the one that is
currently fitted. If so, replace

(4.2 "Orifice replacement")

it.

Note

The current gas category is stated on the type plate.

4. Referring to the gas table

(3.4.3 "Gas data")

, determine whether the main

orifice for the intended gas category is different from the one that is currently
fitted. If so, replace

(4.2 "Orifice replacement")

it.

5. Referring to the gas table

(3.4.3 "Gas data")

, determine whether the use of

a blank plate or burner pressure regulator is required for the intended gas
category. If this is different than for the current gas category,
exchange

(4.3 "Replacement of burner pressure regulator or blank plate

BFM30-50-80-100")

it.

6. Referring to the gas table

(3.4.3 "Gas data")

, determine whether the supply

pressure and burner pressure for the intended gas category correspond with
those for the current gas category, and adjust

(3.11 "Checking the supply

pressure and burner pressure")

these if necessary.

«
...
37
38
39
40
41
...
»

Содержание BFM - 100











































































Отзывы:

Нет отзывов

Похожие инструкции для BFM - 100

Бренд: VEAB Heat Tech Страницы: 40

Бренд: Hamilton Beach Страницы: 18

Бренд: YANGTECH Страницы: 16

Бренд: Ebsray Страницы: 12

Бренд: VARISCO Страницы: 16

Бренд: Dashan Страницы: 20

Бренд: Zoeller Страницы: 12

Бренд: YAMADA Страницы: 18

Бренд: Radialight Страницы: 10

RJS-75SS Series

Бренд: red lion Страницы: 32

Бренд: Eliz Страницы: 20

Бренд: HeatStar Страницы: 60

Бренд: PerformancePro Страницы: 15

Pond Clear 5000

Бренд: SuperFish Страницы: 12

Бренд: salmson Страницы: 68

Бренд: WilTec Страницы: 8

HYDROMATIC SP50

Бренд: Pentair Pool Products Страницы: 12

PROTÉGÉ RPAGP

Бренд: Raypak Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды