A.O. Smith BFM - 100 Скачать руководство пользователя страница 36

Страница: 36 / 74

Installation

Instruction manual BFM

3.11 Checking the supply

pressure and burner
pressure

Note

Before starting the appliance and/or checking the supply pressure and

burner pressure, you must fill

(5 "Filling")

the appliance.

Caution

Before starting up for the first time or after conversion, you must always

check the supply pressure and burner pressure.

Note

The easiest way to check the gas pressures is by using two pressure

gauges. This procedure assumes that these two gauges are available.

If the appliance is to be run on a different gas category than the factory preset
gas category (see type plate) then you must first convert

(4 "Conversion to a

different gas category")

the appliance.

Gas control for BFM 30 through 100

Legend

1. burner pressure regulator
2. burner pressure regulator cap
3. burner pressure regulator

adjustment screw

4. gas control connector
5. blank plate
6. supply pressure test nipple
7. gas control
8. manifold test nipple

IMD-0256 R1

Содержание BFM - 100











































































Результаты поиска

Содержание BFM - 100

Отзывы:

Похожие инструкции для BFM - 100

Бренды по названию

Популярные бренды

A.O. Smith BFM - 100, Инструкция по установке и обслуживанию

Результаты поиска

Содержание BFM - 100

Отзывы:

Похожие инструкции для BFM - 100

Бренды по названию

Популярные бренды