A.O. Smith BFM - 100 Скачать руководство пользователя страница 58

Страница: 58 / 74

Instruction manual BFM

11.2 Troubleshooting: general errors

Warning

Maintenance may only be performed by a qualified service and maintenance engineer.

General errors

Symptom

Cause

Solution

Remark

Gas smell

Gas leak

Warning

Close the main gas valve immediately.

Warning

Do not operate any switches.

Warning

No naked flames.

Warning

Ventilate the boiler room.

Warning

Contact your installation engineer or local gas company

immediately.

Water leakage

Leakage from a water

connection (threaded)

Tighten the threaded connection

If the leak persists, consult your installation engineer

Leakage from another

nearby water appliance

or pipe segment

Trace the leak

Leakage from the

appliance's tank

Consult the supplier and/or manufacturer

Condensation

Before drawing (too much) tap water, wait until the water in the

boiler has reached the set temperature.

Explosive ignition

Poor flame profile

Incorrect supply

pressure and/or burner

pressure

Set the correct supply pressure and/or burner

pressure.

(3.11 "Checking the supply pressure and burner

pressure")

If ignition is not improved, consult your installation engineer.

Contaminated burner

Clean the burner(s)

(12.4.2 "Clean the burner(s)")

Contaminated orifice

Clean the orifice(s)

(12.4.3 "Clean the orifice(s)")

Inadequate air supply

Improve the air supply by providing better ventilation in the boiler

room.

Содержание BFM - 100











































































Результаты поиска

Содержание BFM - 100

Отзывы:

Похожие инструкции для BFM - 100

Бренды по названию

Популярные бренды

A.O. Smith BFM - 100, Инструкция по установке и обслуживанию

Результаты поиска

Содержание BFM - 100

Отзывы:

Похожие инструкции для BFM - 100

Бренды по названию

Популярные бренды