A.O. Smith BFM - 100 Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 74

background image

Introduction

8

Instruction manual BFM

1

gis

Furthermore, the installation must comply with the manufacturer's instructions.

Note

Later amendments and/or additions to all regulations, requirements and

guidelines published on or prior to the moment of installing, will apply to the
installation.

1.4

Maintenance

A service should be carried out at least once a year, both on the water side and
on the gas side. Maintenance frequency depends, among other things, on the
water quality, the average burning time per day and the set water temperature.

Note

To determine the correct maintenance frequency, it is recommended to

arrange for the service and maintenance engineer to check the appliance on
both the water and gas side within three months following installation. Based on
this check, the best maintenance frequency can be determined.

Note

Regular maintenance extends the service life of the appliance.

Note

Both the end user and the service and maintenance engineer are

responsible for regular maintenance. They will need to establish clear
agreements on this.

Note

If the appliance is not regularly maintained, the warranty will become void.

1.5

Forms of notation

The following notation is used in this manual:

Note

Important information.

Caution

Ignoring this information can lead to the appliance being damaged.

Warning

Failure to carefully read this information may lead to personal injury and

serious damage to the appliance.

1.6

Target groups

The three target groups for this manual are:
•

(end) users;

•

installation engineers;

•

service and maintenance engineers.

Symbols on each page indicate the target groups for whom the information is
intended. See the table.

Target group symbols

Symbol

Target group

(End) user

Installation engineer

Service and maintenance engineer

«
...
6
7
8
9
10
...
»

Содержание BFM - 100











































































Отзывы:

Нет отзывов

Похожие инструкции для BFM - 100

Бренд: Nectre Fireplaces Страницы: 17

Бренд: WaterBoss Страницы: 36

Бренд: SAHP Страницы: 41

Бренд: laguna Страницы: 24

Бренд: Navien Страницы: 108

Бренд: Rainfresh Страницы: 10

Бренд: TABLE HEATERS Страницы: 27

Бренд: laguna Страницы: 24

Бренд: VacPak-It Страницы: 9

Бренд: Rheem Страницы: 15

Бренд: AKO Страницы: 6

Бренд: Precision Страницы: 15

Бренд: Reefe Страницы: 12

Бренд: Davey Страницы: 20

Бренд: Yoer Страницы: 20

Бренд: CTC Union Страницы: 28

Бренд: Morton Страницы: 32

Бренд: salmson Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды