A.O. Smith BFM - 100 Скачать руководство пользователя страница 38

Страница: 38 / 74

Installation

Instruction manual BFM

11. Use the pressure gauge to read the burner pressure at nipple (8). Refer to

the gas data table

(3.4.3 "Gas data")

Note

If the burner pressure is incorrect and the appliance is fitted with a blank

plate or high-low control, then you

cannot adjust

the pressure. In this case,

consult your installation engineer or supplier. If the appliance is indeed fitted
with a burner pressure regulator, then you can adjust the pressure.

12.

BFM 30, 50, 80, 100

13. Remove the cap (2) from the burner pressure regulator.
14. Depending on the correction required, correct the burner pressure by turning

adjustment screw (3):
-

Adjustment screw anticlockwise: burner pressure decreases.

Adjustment screw clockwise: burner pressure increases.

15.

BFM 120

16. Remove the cap (2) from the burner pressure regulator.
17. Depending on the correction required, correct the burner pressure by turning

adjustment screw (3) (PG) using the Allen key supplied with the appliance:
-

Adjustment screw anticlockwise: burner pressure decreases.

Adjustment screw clockwise: burner pressure increases.

Warning

Adjustment screw (Ps) adjusts the starting pressure. This need not, and

must never be adjusted from the factory preset.

18. Check the burner pressure against the value given in the gas

table

(3.4.3 "Gas data")

19. If the pressure reading is not correct, repeat the burner pressure adjustment

until the correct pressure is obtained.

20. Shut down the appliance by setting the 0/1 switch to position 0.
21. Shut off the gas supply.
22. Disconnect the two pressure gauges and re-tighten the sealing screws in the

test nipples.

Note

Before starting-up the appliance, take time to fill in the warranty card

supplied with the appliance. This enables us to guarantee the quality of our
systems and further enhance our warranty procedure.

Please return this card as soon as possible. Your customer will then receive a
warranty certificate with our warranty conditions

Содержание BFM - 100











































































Результаты поиска

Содержание BFM - 100

Отзывы:

Похожие инструкции для BFM - 100

Бренды по названию

Популярные бренды

A.O. Smith BFM - 100, Инструкция по установке и обслуживанию

Результаты поиска

Содержание BFM - 100

Отзывы:

Похожие инструкции для BFM - 100

Бренды по названию

Популярные бренды