A.O. Smith BFM - 100 Скачать руководство пользователя страница 66

Страница: 66 / 74

Performing maintenance

Instruction manual BFM

12.4 Gas-side mainte-

nance

12.4.1

Introduction

The following steps must be carried out on the gas side:
1.

Clean the burner(s)

Clean the orifice(s)

Checking the flue baffles

12.4.2

Clean the burner(s)

1. Detach the burner(s)
2. Remove all contamination present on the burner(s).
3. Fit the burner(s)

12.4.3

Clean the orifice(s)

1. Detach the orifice(s)
2. Remove all contamination present in the orifice(s).
3. Fit the orifice(s)

12.4.4

Checking the flue baffles

Warning

The flue baffles can be hot.

1. Remove the flue baffles from the appliance.
2. Check the flue baffles for the presence of corrosion, removing this if

necessary.

3. Check the flue baffles for wear, and replace the flue baffles if necessary.

12.5 Finalising mainte-

nance

To finalise the maintenance, carry out the following steps:
1. Fill the appliance

(5 "Filling")

2. Start the appliance

(9 "Starting and running")

Содержание BFM - 100











































































Результаты поиска

Содержание BFM - 100

Отзывы:

Похожие инструкции для BFM - 100

Бренды по названию

Популярные бренды

A.O. Smith BFM - 100, Инструкция по установке и обслуживанию

Результаты поиска

Содержание BFM - 100

Отзывы:

Похожие инструкции для BFM - 100

Бренды по названию

Популярные бренды