A.O. Smith BFM - 100 Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 74

background image

Installation

18

Instruction manual BFM

3

is

3.3.2

Maximum floor load

Allow for the appliance's weight with respect to the maximum floor load; refer to
the table.

3.3.3

Water composition

The appliance is intended for heating drinking water. The drinking water must
comply with the regulations governing drinking water for human consumption.
The table gives an overview of the specifications.

Water specifications

Note

If the water specifications deviate from those stated in the table, then the

tank protection cannot be guaranteed

(13 "Warranty (certificate)")

.

3.3.4

Working clearances

For access to the appliance, it is recommended that the following clearances
are observed (see figure):
•

AA: around the appliance's control column and cleaning openings: 100cm.

•

BB: all sides of the appliance: 50cm.

•

Above the appliance (room to replace the anodes):
-

100cm if using fixed anodes, or

-

50cm if using flexible anodes.

If the available clearance is less than 100cm, flexible magnesium anodes
may be ordered.

Note

When installing the appliance, be aware that any leakage from the tank

and/or connections can cause damage to the immediate environment or floors
below the level of the boiler room. If this is the case, the appliance should be
installed above a wastewater drain or in a suitable metal leak tray.
The leak tray must have an appropriate wastewater drain and must be at least
5cm deep with a length and width at least 5cm greater than the diameter of the
appliance.

Weight of the appliance filled with water

BFM 30 BFM 50 BFM 80 BFM 100

BFM 120

539 kg

543 kg

548 kg

573 kg

573 kg

Water composition

Hardness

(alkaline earth ions)

> 1.00 mmol/l:
•

German hardness> 5.6° dH

•

French hardness > 10.0° fH

•

English hardness > 7.0° eH

Conductivity

> 125 µS/cm

Acidity (pH value)

7.0 < pH value < 9.5

«
...
16
17
18
19
20
...
»

Содержание BFM - 100











































































Отзывы:

Нет отзывов

Похожие инструкции для BFM - 100

Knockonwood DBE KNUF

Бренд: Jaga Страницы: 4

Бренд: Jaga Страницы: 8

Бренд: Jaga Страницы: 12

Clima Canal JDPC.002

Бренд: Jaga Страницы: 8

Бренд: A.O. Smith Страницы: 4

Бренд: BLACKMER Страницы: 24

Бренд: Mr. Heater Страницы: 7

Бренд: Celsius Страницы: 4

Бренд: Webasto Страницы: 12

Бренд: CLAS Страницы: 20

MORRIS MPH-20041S

Бренд: TUYA Страницы: 11

Бренд: Euromatic Страницы: 16

Бренд: Black Knight Страницы: 15

Бренд: Lasko Страницы: 4

Бренд: Belief Страницы: 20

MegaLife HE Series

Бренд: Heatrae Sadia Страницы: 24

Бренд: Gabarron Страницы: 9

Бренд: V.I.I. Страницы: 21

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды