A.O. Smith BFM - 100 Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 74

background image

Instruction manual BFM

35

is

In preparation you should first remove the two plastic covers and the
protective cap of the electrical section.
1. Undo the screws of the plastic covers.
2. Carefully remove the covers from the appliance.

The electrical section is now visible.

3. Loosen the 2 screws (A) of the electrical section, and remove the protective

cover (B) from the electrical section.
The connector block (C) is now visible.

Note

Refer to the table for connections 1 through 10.

Consult the electrical diagram

(14 "Electrical diagram")

for the electrical

component connections.

Electrical connector block

3.10.1

Connecting the mains power

The appliance is supplied without a power cable and isolator.

Note

In order to receive electrical power, the appliance has to be connected to the

mains power by means of a permanent electrical connection. A double-pole
isolator with a contact gap of at least 3 mm must be fitted between this
permanent connection and the appliance. The power cable must have cores of
at least 3 x 1.0 mm

2

.

Warning

Leave the appliance isolated until you are ready to start it up.

1. Feed the power cable through the metric strain relief to the top side of the

control column.

2. Connect the earth ( ), live (L

1

) and neutral (N) of the power cable to

terminals 1 through 3 in the connector block as stated in the table.

3. Turn the strain relief tight to clamp the lead.
4. If you do not need to make any more connections, fit the protective cover

onto the control column.

5. Connect the power cable to the isolator.

Warning

>Leave the appliance electrically isolated until you are ready to start it up.

Mains power

Fan

Alarm Off

N

L1

N

L

S1

S2

S3

S4

1

2

3

4

5

6

7

8

9

10

«
...
33
34
35
36
37
...
»

Содержание BFM - 100











































































Отзывы:

Нет отзывов

Похожие инструкции для BFM - 100

Бренд: Lasko Страницы: 4

Бренд: salmson Страницы: 12

607 challenger series

Бренд: National Vacuum Equipment Страницы: 20

Бренд: TapFlo Страницы: 63

Бренд: I.VA.CO. Страницы: 12

Бренд: Kamco Страницы: 36

Бренд: Flotec Страницы: 24

Бренд: Elkay Страницы: 6

Бренд: easy Maxx Страницы: 37

Бренд: Walrus Pump Страницы: 12

JABSCO 18670 Series

Бренд: Xylem Страницы: 16

Бренд: vacuubrand Страницы: 70

Бренд: L.B. White Страницы: 24

Бренд: salmson Страницы: 24

Бренд: Vectra Fitness Страницы: 28

Бренд: THERMEx Страницы: 36

Бренд: Ducar Страницы: 30

Бренд: Gardena Страницы: 17

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды