3DHISTECH Ltd. Pannoramic DESK II Скачать руководство пользователя

Страница: 71 / 82

Pannoramic DESK II 1.23 User’s Guide

5 Troubleshooting and Maintenance

1. Remove both Allen screws

(2)

located at the left and right sides of the cover

(1)

by using an

Allen screwdriver

(3)

2. Carefully push the cover

(5)

horizontally frontward with light pressure until it can be

removed completely from the basic unit

(4)

3. When you have finished maintenance or repair work, reattach the cover. Push it horizontally

towards the basic unit

(4)

until the two protruding guide pins

(6)

fit into the corresponding

recesses of the basic unit.

4. Note that the rear part of the cover must be pushed over the top part of the blue basic unit

(7)

5. To lock the cover in place, insert the screws again and fasten them.

Caution!

Make sure that no cables are squeezed as you replace the cover(s).

5.3.2 Removing a slide

If a slide got jammed or has suffered breakage during the process of digitization, stop the process
and, if possible, move the slide holder to a position where the slide can be easily removed.

Warning!

Crush hazard! Before you remove a jammed slide, cancel

the running

digitization process, terminate the software session and turn the power

off.

Any manipulation performed on a mechanical component must be followed by a complete device

initialization routine (software restart).

June 4, 2018 - Rev. 2

3DHISTECH Ltd.

(

)

Содержание Pannoramic DESK II



















































































Результаты поиска

Содержание Pannoramic DESK II

Отзывы:

Похожие инструкции для Pannoramic DESK II

Бренды по названию

Популярные бренды

3DHISTECH Ltd. Pannoramic DESK II, Руководство пользователя

Результаты поиска

Содержание Pannoramic DESK II

Отзывы:

Похожие инструкции для Pannoramic DESK II

Бренды по названию

Популярные бренды