3D Systems SLA 750 Series Скачать руководство пользователя страница 2

Страница: 2 / 101

TABLE OF CONTENTS

SLA 750 SERIES INTRODUCTION ..................................................................................................... 1

SLA 750 SERIES SAFETY .....................................................................................................................2

SLA 750 SERIES ENVIRONMENTAL CONDITIONS ........................................................................14

SLA 750 SERIES HARDWARE OVERVIEW ....................................................................................... 15

4.1 Production Printer .......................................................................................................................................................................15

SLA 750 SERIES SPECIFICATIONS AND REQUIREMENTS ............................................................ 23

SLA 750 SERIES USER INTERFACE OVERVIEW .............................................................................. 24

6.5 Elevator and Recoater .................................................................................................................................................................38

6.6 Laser ..............................................................................................................................................................................................45
6.7 Material .........................................................................................................................................................................................48

6.7.1 Leveling the Material .........................................................................................................................................................49
6.7.2 Removing bubbles .............................................................................................................................................................52

3D Systems, Inc.

p/n 40-D150, Rev. C

Содержание SLA 750 Series






































































































Результаты поиска

Содержание SLA 750 Series

Отзывы:

3D Systems SLA 750 Series, Руководство пользователя, Страница: 2 / 101

Результаты поиска

Содержание SLA 750 Series

Отзывы: