3D Systems SLA 750 Series Скачать руководство пользователя страница 25

Страница: 25 / 101

• On, Solid > Ready is seen for when any pre-checks succeeds
• On, Flashing >
• Off >

4.4 Transfer Cart

The transfer cart is an optional accessory. The transfer cart allows you to easily remove a large or heavy print platform from

the printer. It is then wheeled to the finishing area where supports are removed from the printed part and cleaned before it is

cured.
Safety

CAUTION: Before / After Each Use - Inspect transfer carts routinely and do not use them if they are not in good

repair.

CAUTION: Safe load height or in a manner that will not obstruct vision.

CAUTION: Pay attention to the path of travel and do not move too fast.

CAUTION: Follow recommended maximum load limits of 113kg (250lbs)

CAUTION: Do not try to navigate on stairs or steep inclines.

CAUTION: When not in use, the transfer cart should be parked in a designated area.

Refer to the section,

Using the Transfer Cart

for information on operating the cart.

3D Systems, Inc.

p/n 40-D150, Rev. C

Содержание SLA 750 Series






































































































Результаты поиска

Содержание SLA 750 Series

Отзывы:

3D Systems SLA 750 Series, Руководство пользователя, Страница: 25 / 101

Результаты поиска

Содержание SLA 750 Series

Отзывы: