3D Systems SLA 750 Series Скачать руководство пользователя страница 49 | Manualshive

Страница: 49 / 101

3D Systems SLA 750 Series Скачать руководство пользователя страница 49

6.6 Laser

1

Laser Emission: Allows you to manually turn the laser on or off. When you start a build the laser automatically turns

on.

2

Shutter: Switch the laser beam shutter between open and closed.

3

Spot: Toggles the laser beam spot size between large and small.

4

Set Laser Power: Opens dialog to set laser power in milliwatt.

5

Back, Front, Left, Right and Stop: Manual motion control for the laser beam. Hold the arrow down to move.

6

Y Position: Current Y position of the laser beam
Y Move To: Set the value to manually adjust the laser beam along the y-axis. To move the laser beam, use the move

laser beam arrows.

7

X Position: Current X position of the laser beam
X Move To: Set the value to manually adjust the laser beam along the x-axis. To move the laser beam, use the move

laser beam arrows.

3D Systems, Inc.

45

p/n 40-D150, Rev. C

«
...
47
48
49
50
51
...
»

Содержание SLA 750 Series






































































































Отзывы:

Нет отзывов