3D Systems SLA 750 Series Скачать руководство пользователя страница 44 | Manualshive

Страница: 44 / 101

3D Systems SLA 750 Series Скачать руководство пользователя страница 44

6.5.1 Setting the print platform start position

Setting the Start Position
The Start Position is the position of the print platform when the machine is set up for optimal printing success.
The start position will need to be set when the printer is first set up or when any of the following conditions exist:
• The top of the print platform is completely/partially submerged (See Figure A).
• The platform to resin level is just right (See Figure B).
• The top of the print platform is raised above resin surface (See Figure C).

Figure A - Platform is partially

submerged

Figure B - Platform to resin level is just

right

Figure C - Platform is above resin surface

Note: If any holes are completely or partially submerged and or if the print platform is above the resin level,

the Start Position must be set.

To Set the Start Position:

1. From the UI, tap on Elevator & Recoater (1) near the bottom tray and tap on More Settings.
2. Tap Move to Start (2). This will bring the build platform to the starting position.
3. Tap Level Material (3).

3D Systems, Inc.

40

p/n 40-D150, Rev. C

«
...
42
43
44
45
46
...
»

Содержание SLA 750 Series






































































































Отзывы:

Нет отзывов