3D Systems SLA 750 Series Скачать руководство пользователя страница 100

Страница: 100 / 101

SLA 750 SERIES LEGAL NOTICES

contains proprietary information that is the property of 3D Systems, Inc. The licensed user, in the name of whom this document

is registered (the "Licensed User") does not have the right to copy, reproduce, or translate this document in any way or to any

media without the prior written consent of 3D Systems, Inc. No copies of the document may be sold or given to any person or

other entity.
FCC NOTICE
This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to Part 15 of

the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment

is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if

not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful interference in which case, the user will be required

to correct the interference at his own expense.

Note: Changes or modifications to this equipment not specifically approved by 3D Systems may void the user's

authority to operate this equipment.

RADIO FREQUENCY TRANSMISSION
This product generates 13.56 MHz using an Inductive Loop System as a Radio Frequency Identification device (RFID). This

RFID device complies with the requirements specified in FCC Part 15, Industry Canada RSS-210, Radio Equipment Directive

2014/53/EU, and all applicable local laws and regulations. Operation of this device is subject to the following two conditions:

(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including

interference that may cause undesired operation. The device referenced in this guide contains transmitter, FCC ID: 2ADGF-

CLDRIDQK IC: 12666A-CLDRIDQK. Access to the transmitter for service technicians is available through common enclosure

access methods including use of common tools and removal of covers.

Note: Changes or modifications to this equipment not specifically approved by 3D Systems may void the user's

authority to operate this equipment.

Korean Warning Statement for product manual, For Class A Device (Commercial/Office Use):

3D Systems, Inc.

p/n 40-D150, Rev. C

Содержание SLA 750 Series






































































































Результаты поиска

Содержание SLA 750 Series

Отзывы:

3D Systems SLA 750 Series, Руководство пользователя, Страница: 100 / 101

Результаты поиска

Содержание SLA 750 Series

Отзывы: